manualshive.com logo in svg

Exar XRT86VL38, Manual

The Exar XRT86VL38 user manual is available for free download on manualshive.com. This comprehensive manual provides detailed instructions, troubleshooting tips, and useful insights for maximizing the potential of your XRT86VL38. Accessible in a few clicks, this manual will assist you in harnessing the full power of your XRT86VL38.

Share
Download
background image

xr

PRELIMINARY

XRT86VL38

REV. P1.0.6 

OCTAL T1/E1/J1 FRAMER/LIU COMBO

148

T

ABLE

 60: DS1/E1 T

EST

 R

EGISTER

 1

R

EGISTER

 33                                                     DS1/E1 T

EST

 R

EGISTER

 1 (TR1)                                                      0

XN

123

B

IT

F

UNCTION

T

YPE

D

EFAULT

D

ESCRIPTION

-O

PERATION

7

PRBSTyp

R/W

0

PRBS Pattern Type

This READ/WRITE bit-field selects the type of PRBS pattern that the 
T1/E1 Transmit/Receive framer will generate or detect. PRBS 15 

(X

15

 + X

14

 +1) Polynomial or QRTS (Quasi-Random Test Signal) 

Pattern can be generated by the transmit or receive framer depend-
ing on whether PRBS switch function is enabled or not (Test Regis-
ter 2 (TR2), Address 0xn121, bit 3 set to 1). 

If the PRBS Switch function is disabled, T1/E1 transmit framer will 
generate either PRBS 15 or QRTS pattern and output to the line 
interface. PRBS 15 or QRTS pattern depends on the setting of this 
bit.

If the PRBS Switch function is enabled, T1/E1 receive framer will 
generate either PRBS 15 or QRTS pattern and output to the receive 
back plane interface. PRBS 15 or QRTS pattern depends on the 
setting of this bit.

0 = Setting this bit to ‘0’ will enable the PRBS 15 (X

15

 + X

14

 +1) 

Polynomial generation.

1 = Setting this bit to ‘1’ will enable the QRTS (Quasi-Random Test 
Signal) pattern generation.

6

ERRORIns

R/W

0

Error Insertion

This READ/WRITE bit-field is used to insert a single PRBS/QRTS 
error to the transmit or receive output depending on whether PRBS 
switch function is enabled or not. (Test Register 2 (TR2), Address 
0xn121, bit 3 set to 1). 

If the PRBS Switch function is disabled, T1/E1 transmit framer will 
insert a single PRBS/QRTS error and output to the line interface if 
this bit is enabled. 

If the PRBS Switch function is enabled, T1/E1 receive framer will 
insert a single PRBS/QRTS error and output to the receive back 
plane interface if this bit is enabled. 

A ‘0’ to ‘1’ transition will cause one output bit inverted in the PRBS/
QRTS stream.

This bit only works if PRBS generation

Summary of Contents for XRT86VL38



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XRT86VL38

Hama PM-Pro 3 User Manual preview
PM-Pro 3
Brand: Hama Pages: 5
FnL SRD7104P Quick Installation Manual preview
SRD7104P
Brand: FnL Pages: 6
Keithley KPCI-3101 Series User Manual preview
KPCI-3101 Series
Brand: Keithley Pages: 146
SanDisk MobileMate Micro Memory User Manual preview
MobileMate Micro Memory
Brand: SanDisk Pages: 2
Acard AEC-67160 Ultra160 User Manual preview
AEC-67160 Ultra160
Brand: Acard Pages: 39
bioscrypt V-Prox Setup Manual preview
V-Prox
Brand: bioscrypt Pages: 72
Advantech PCIE-1765 User Manual preview
PCIE-1765
Brand: Advantech Pages: 24
AMX ANT-RDR Installation Manual preview
ANT-RDR
Brand: AMX Pages: 2
MSI StarReader Specifications preview
StarReader
Brand: MSI Pages: 1
Farpointe Data Delta3 Quick Start Manual preview
Delta3
Brand: Farpointe Data Pages: 2
Broadcom BCM94360HMB User Manual preview
BCM94360HMB
Brand: Broadcom Pages: 15
Broadcom BCM943602BAED User Manual preview
BCM943602BAED
Brand: Broadcom Pages: 16
NanoEnTek Frend system User Manual preview
Frend system
Brand: NanoEnTek Pages: 57
ZyXEL Communications NWD672NU User Manual preview
NWD672NU
Brand: ZyXEL Communications Pages: 11
Exsys EX-41062 User Manual preview
EX-41062
Brand: Exsys Pages: 2
Exsys EX-45032 Manual preview
EX-45032
Brand: Exsys Pages: 20
Lindy SD-FW323-3I User Manual preview
SD-FW323-3I
Brand: Lindy Pages: 4
Nordic ID ID EXA31 Quick Manual preview
ID EXA31
Brand: Nordic ID Pages: 4

Brands by name

Popular brands

Load more brands