Dell 3110 Color Laser User Manual Download Page 129

Page: 129 / 451

Insert all media face down and top edge first into the multipurpose feeder.

NOTE:

Do not force the print media.

Slide both width guides until they rest lightly against the edge of the print media stack.

NOTE:

Be careful not to bend the print media.

Make sure the type setting for the multipurpose feeder is set to the correct value for the print media
you have loaded.

Select print media source, size, and type in your software program and select the print media size and
type on the printer operator panel.

Loading Envelopes

To load envelopes in the multipurpose feeder, insert the envelopes with the flaps closed and the short-edge

Summary of Contents for 3110 Color Laser




































































































































































































































































































































































































































































Search results

Summary of Contents for 3110 Color Laser

Reviews:

Related manuals for 3110 Color Laser

Brands by name

Popular brands

Dell 3110 Color Laser, User Manual

Search results

Summary of Contents for 3110 Color Laser

Reviews:

Related manuals for 3110 Color Laser

Brands by name

Popular brands