Dell 3110 Color Laser User Manual Download Page 424

Page: 424 / 451

Gradation

Auto

For Transparency

-Gg=

mode

Specifies gray guaranteed.
Available gray guaranteed options are as follows.

off

Off

This option is available only for color printing.

-Ct

Specifies color transformation.
This option is available only for color printing.

-Br=

mode

Specifies brightness adjustment.

Available brightness adjustment option value are as follows.

Bright 5

Bright 4

Bright 3

Bright 2

Summary of Contents for 3110 Color Laser




































































































































































































































































































































































































































































Search results

Summary of Contents for 3110 Color Laser

Reviews:

Related manuals for 3110 Color Laser

Brands by name

Popular brands

Dell 3110 Color Laser, User Manual

Search results

Summary of Contents for 3110 Color Laser

Reviews:

Related manuals for 3110 Color Laser

Brands by name

Popular brands