Dell 3110 Color Laser User Manual Download Page 65 | Manualshive

Page: 65 / 451

background image

1 Ethernet port

2 Optional wireless printer adapter socket

To connect the printer to the network, plug one end of an Ethernet cable into the Ethernet port on the back
of the printer, and the other end into a LAN drop or hub. For a wireless connection, insert the wireless
printer adapter into the wireless printer socket on the back of the printer.

Turn On the Printer

Plug one end of the printer power cable into the socket at the back of the printer and the other end
into a properly grounded outlet.

1.

CAUTION:

Do not use extension cords or power strips.

2.

«
...
63
64
65
66
67
...
»

Summary of Contents for 3110 Color Laser




































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 3110 Color Laser

Brand: WANHAO Pages: 29

Brand: QMS Pages: 86

Brand: Nantian Electronics Pages: 4

Brand: Unimark Pages: 38

Brand: BIXOLON Pages: 59

Brand: Konica Minolta Pages: 44

Brand: Xiamen Hanin Electronic Technology Pages: 27

Brand: LaserLine Pages: 14

Brand: Oce Pages: 230

apeosport-v c5585

Brand: Fuji Xerox Pages: 493

Brand: Intermec Pages: 2

Suprasetter 106

Brand: HEIDELBERG Pages: 91

Brand: UnionTech Pages: 44

Brand: Skip-Line Pages: 11

Brand: Olivetti Pages: 97

ET-M1170 Series

Brand: Epson Pages: 133

Brand: Sawgrass Pages: 22

ML-3561N Series

Brand: Samsung Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands