Dell 3110 Color Laser User Manual Download Page 440

Page: 440 / 451

The setting is complete. Execute printing from the software program.

Uninstalling the Printer Driver

Select

Main Menu

System Tools

Terminal

Type the following command in the terminal window.

(Type the administrator's password)

rpm -e Dell-Color-Laser-3110cn

The printer driver is uninstalled.

Operation on SUSE 9.2/9.3

Installing the Printer Driver

Double-click

Dell-Color-Laser-3110cn-x.x-x.noarch.rpm

in the

Drivers and Utilities

CD.

Click

Install package with YaST

Type the administrator's password.
Installation starts. When the installation is complete, the window is automatically closed.

Setting Up the Queue

To execute printing, you must set up the print queue on your workstation.

Select

Start Applications

System

YaST

Type the administrator's password.

YaST Control Center

is activated.

Select

Hardware

from

Printer

Printer setup: Autodetected printers

is activated.

For USB connections:

Select

Dell Color Laser 3110cn on USB

(

//Dell/Color%20Laser%203110cn or

/dev/usblp

*) as

Available are

, and then click

Configure...

Confirm the settings in

Edit configuration

, and then click

Summary of Contents for 3110 Color Laser




































































































































































































































































































































































































































































Search results

Summary of Contents for 3110 Color Laser

Reviews:

Related manuals for 3110 Color Laser

Brands by name

Popular brands

Dell 3110 Color Laser, User Manual

Search results

Summary of Contents for 3110 Color Laser

Reviews:

Related manuals for 3110 Color Laser

Brands by name

Popular brands