Dell 3110 Color Laser User Manual Download Page 66 | Manualshive

Page: 66 / 451

background image

CAUTION:

The printer should not be plugged into a UPS system.

Turn on the computer and the printer.

2.

Print and Check the Printer Settings Page

Print a printer settings page to verify the network connection. This page also provides important information
that helps you configure for network printing.

NOTE:

Depending on the network configuration, the printer may not be provided an IP address

immediately. If the Printer Settings page does not show an assigned IP address, wait 5 minutes and
try again.

Press

Menu

.

1.

Press

until

Report/List

appears, and then press

.

2.

Printer Setting

is displayed

.

Press

.

3.

The printer settings page is printed.

If the IP address shows anything other than

0.0.0.0

(the factory default) or 169.254.xx.xx, the printer

has an IP address assigned and stored. Go to "

Verify the IP Settings

."

4.

Assign an IP Address

NOTE:

When you assign an IP address manually in

IPv6 Mode

, use the

Dell Printer Configuration

Web Tool

. To open the

Dell Printer Configuration Web Tool

, use the link local address. (To check

a link local address, see "

Print and Check the Printer Settings Page

".)

An IP address is a unique number that consists of four sections that are delimited by a period and can
include up to three digits in each section, for example, 111.222.33.44.

Assigning an IP address already in use can cause network performance issues.

NOTE:

Assigning an IP address is considered as an advanced function and is normally done by a

system administrator.

For more information on using your operator panel, see "

Operator Panel

."

Turn on the printer.

1.

The

Ready to Print

appears.

2.

«
...
64
65
66
67
68
...
»

Summary of Contents for 3110 Color Laser




































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 3110 Color Laser

Brand: Olympus Pages: 71

Brand: uBuild-3D Pages: 12

Brand: Xerox Pages: 2

Brand: Xerox Pages: 130

Brand: Xerox Pages: 793

Brand: Muratec Pages: 213

IMAGE M4100 Series

Brand: G&G Pages: 147

Brand: Oki Pages: 20

B-470-QQ Series

Brand: TEC Pages: 32

Brand: Konica Minolta Pages: 12

EuroLine Series

Brand: Output Technology Pages: 73

Brand: Savin Pages: 4

Brand: MIMAKI Pages: 20

Brand: Pantum Pages: 111

Brand: Microcom Pages: 207

Markoprint X4JET

Brand: Weber Pages: 177

Brand: Xerox Pages: 244

Brand: Jetmobile Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands