Dell 3110 Color Laser User Manual Download Page 296 | Manualshive

Page: 296 / 451

background image

Replace the tray into the printer.

3.

Replacing the Belt Unit

CAUTION:

Before performing any of the following procedures, read and follow the safety

instructions in your

Owner's Manual

.

NOTICE:

Make sure nothing touches or scratches the surface (black-colored film) of the belt unit.

Scratches, dirt, or oil from your hands on the film of the belt unit may reduce print quality.

NOTICE:

To protect the drums of the print cartridges against bright light, close the front cover within

5 minutes. If the front cover remains open for more than 5 minutes, print quality may deteriorate.

Dell belt units are available only through Dell. To order by phone, see your

Owner's Manual

. Dell

recommends Dell belt units for your printer. Dell does not provide warranty coverage for problems caused by
using accessories, parts, or components not supplied by Dell.

Removing the Used Belt Unit

NOTE:

Remove any print jobs from the center output tray, and close the multipurpose feeder cover

before opening the front cover.

Make sure that the printer is turned off.

1.

Push the side button and open the front cover.

2.

«
...
294
295
296
297
298
...
»

Summary of Contents for 3110 Color Laser




































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 3110 Color Laser

MultiPASS L6000

Brand: Canon Pages: 251

MultiPASS C5500

Brand: Canon Pages: 24

MultiPASS L6000

Brand: Canon Pages: 24

Laser Class 700 Series

Brand: Canon Pages: 221

Brand: IBM Pages: 16

Brand: Samsung Pages: 2

Brand: TallyGenicom Pages: 175

Brand: Oki Pages: 40

Brand: Oki Pages: 104

Brand: Oki Pages: 28

Brand: Oki Pages: 23

Brand: Oki Pages: 108

Brand: Oki Pages: 2

Brand: Oki Pages: 94

Brand: Oki Pages: 135

Brand: Oki Pages: 97

Brand: Oki Pages: 280

Brand: Oki Pages: 123

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands