Dell 3110 Color Laser User Manual Download Page 420

Page: 420 / 451

LabelPaper/Labels

Coated/Coated 2/Coated Paper 2

C2B

Coated Back/Coated 2/Coated Paper 2- Side 2

Coated Thick/Coated 3/Coated Paper 3

C3B

Coated Thick Back/Coated 3/Coated Paper 3- Side 2

JapaneseCoatingPaper/Japanese Coated/Japanese Coated Paper

JCB

JapaneseCoatingPaperBack/Japanese Coated/Japanese Coated Paper - Side 2

JapanesePostcard/Japanese Postcard

PCB

JapanesePostcardBack/Japanese Postcard/Japanese Postcard - Side 2

Envelope

If this option is not specified, multipurpose feeder Paper Type of the printer can be used.

-Mfo=

mode

Specifies orientation for multipurpose feeder.
Available orientations for multipurpose feeder are as follows.

Landscape

ler

Landscape (Rotated)

Summary of Contents for 3110 Color Laser




































































































































































































































































































































































































































































Search results

Summary of Contents for 3110 Color Laser

Reviews:

Related manuals for 3110 Color Laser

Brands by name

Popular brands

Dell 3110 Color Laser, User Manual

Search results

Summary of Contents for 3110 Color Laser

Reviews:

Related manuals for 3110 Color Laser

Brands by name

Popular brands