Dell 3110 Color Laser User Manual Download Page 148 | Manualshive

Page: 148 / 451

background image

Wireless Net

Use the Wireless Net menu to change print settings affecting jobs sent to the printer through a wireless
network.

NOTE:

The

Wireless Net

menu is only displayed when an optional multi protocol card is installed on

the printer and the optional wireless printer adapter is installed on the card.

NOTE:

Values marked by an asterisk (*) are the factory default menu settings.

Status

Purpose:

To display the information on the wireless signal strength. Any change cannot be made on the operator
panel to improve the status of the wireless connection.

Values:

Good

Indicates good signal strength.

Acceptable

Indicates marginal signal strength.

Low

Indicates insufficient signal strength.

No Reception

Indicates that no signal is received.

Reset Wireless

Purpose:

To initialize wireless network settings. After executing this function and rebooting the printer, all wireless
network settings are reset to their default values.

TCP/IP

Purpose:

To specify the TCP/IP settings for the wireless network. The change becomes effective after the printer is
turned off and then on again.

«
...
146
147
148
149
150
...
»

Summary of Contents for 3110 Color Laser




































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 3110 Color Laser

WORKCENTRE 5050

Brand: Xerox Pages: 186

7500DX - Phaser Color LED Printer

Brand: Xerox Pages: 5

Brand: Panasonic Pages: 240

Brand: Canon Pages: 21

Brand: Canon Pages: 23

WorkCentre Pro 90

Brand: Xerox Pages: 36

Stacker 701P98048

Brand: Xerox Pages: 16

Brand: WANHAO Pages: 25

Brand: Xerox Pages: 2

Brand: ABLE Systems Pages: 12

Brand: Labelmate Pages: 61

Brand: IriSys Pages: 21

Brand: VuPoint Pages: 20

Pro-LX Pro-LX Laminating Card...

Brand: FARGO electronics Pages: 228

HP Toner Cartridges 6R941

Brand: Xerox Pages: 2

Brand: DPM Pages: 2

Brand: Daewoo Pages: 37

Brand: HCC Technology Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands