Dell 3110 Color Laser User Manual Download Page 307 | Manualshive

Page: 307 / 451

background image

Replacing the Fuser

CAUTION:

To prevent electric shock, always turn off the printer and disconnect the power

cable from the grounded outlet before performing maintenance.

CAUTION:

Before performing any of the following procedures, read and follow the safety

instructions in your

Owner's Manual

.

NOTICE:

To protect the drums of the print cartridges against bright light, close the front cover within

5 minutes. If the front cover remains open for more than 5 minutes, print quality may deteriorate.

NOTE:

Remove any print jobs from the center output tray, and close the multipurpose feeder before

opening the front cover.

Dell fuser are available only through Dell. To order by phone, see your

Owner's Manual

.

Dell recommends Dell fuser for your printer. Dell does not provide warranty coverage for problems caused
by using accessories, parts, or components not supplied by Dell.

Removing the Used Fuser

CAUTION:

To avoid burns, do not replace the fuser immediately after printing, as the fuser

gets very hot during this process.

Turn off the printer and wait for 30 minutes for the fuser to cool down before removal.

1.

Push the side button and open the front cover.

2.

Lift the chute gate to its upright position.

3.

«
...
305
306
307
308
309
...
»

Summary of Contents for 3110 Color Laser




































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 3110 Color Laser

Brand: EBS Pages: 4

Brand: NCR Pages: 38

Brand: Xerox Pages: 168

Brand: Xerox Pages: 36

Brand: Xerox Pages: 64

Brand: Xerox Pages: 54

Brand: Xerox Pages: 2

Brand: Xerox Pages: 115

Brand: Xerox Pages: 2

Aficio SP4100N-KP

Brand: Ricoh Pages: 4

Brand: DNP Pages: 2

Brand: Tally Pages: 106

Brand: Citizen Pages: 3

Brand: Oki Pages: 336

VersaLink Series

Brand: Xerox Pages: 185

Brand: Xerox Pages: 150

5550N - Phaser B/W Laser Printer

Brand: Xerox Pages: 16

Brand: Oce Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands