Dell 3110 Color Laser User Manual Download Page 64 | Manualshive

Page: 64 / 451

background image

CAUTION:

Do not use extension cords or power strips.

CAUTION:

The printer should not be plugged into a UPS system.

Turn on the computer and the printer.

2.

Connecting the Printer to the Network

To attach the printer to a network:

Make sure the printer, computer, and any other attached devices are turned off and unplugged.

1.

Connect the printer to the network using an Ethernet cable or the wireless printer adapter.
To use a wireless printer adapter, you must install the Multi Protocol Card first. To install the card, see
"

Installing the Dell Multi Protocol Card

".

2.

«
...
62
63
64
65
66
...
»

Summary of Contents for 3110 Color Laser




































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 3110 Color Laser

Brand: Canon Pages: 12

imagePROGRAF iPF8300S

Brand: Canon Pages: 52

Brand: Canon Pages: 2

Brand: Xerox Pages: 168

Brand: Xerox Pages: 36

Brand: Xerox Pages: 64

Brand: Xerox Pages: 54

Brand: Xerox Pages: 2

Brand: Xerox Pages: 115

Brand: Samsung Pages: 368

Brand: Durst Pages: 2

Brand: ABLE Pages: 42

Brand: Konica Minolta Pages: 404

Brand: Oce Pages: 330

INFOPRINT HI-LITE COLOR 4005-HC2

Brand: IBM Pages: 10

WorkCentre Pro 421

Brand: Xerox Pages: 162

Brand: Microcom Pages: 207

Suprasetter 106

Brand: HEIDELBERG Pages: 91

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands