manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

937

   

Configuring IPv6 Unicast Routing

Configuring IPv6

EXAMPLE

This example shows how to enable IPv6 with both a link-local address and a global address based on the IPv6 prefix 
2001:0DB8:c18:1::/64. The EUI-64 interface ID is used in the low-order 64 bits of both addresses. Output from the 

show 

ipv6 interface

 EXEC command is included to show how the interface ID (20B:46FF:FE2F:D940) is appended to the 

link-local prefix FE80::/64 of the interface.

Switch(config)# 

sdm prefer dual-ipv4-and-ipv6 default 

Switch(config)# 

ipv6 unicast-routing

Switch(config)# 

interface gigabitethernet0/2

Switch(config-if)# 

no switchport

Switch(config-if)# 

ipv6 address 2001:0DB8:c18:1::/64 eui 64

Switch(config-if)# 

end

Switch# 

show

 

ipv6 interface gigabitethernet0/11

GigabitEthernet0/2 is up, line protocol is up

  IPv6 is enabled, link-local address is FE80::20B:46FF:FE2F:D940

  Global unicast address(es):

2001:0DB8:c18:1:20B:46FF:FE2F:D940, subnet is 2001:0DB8:c18:1::/64 [EUI]

  Joined group address(es):

    FF02::1

    FF02::2

    FF02::1:FF2F:D940

  MTU is 1500 bytes

  ICMP error messages limited to one every 100 milliseconds

  ICMP redirects are enabled

  ND DAD is enabled, number of DAD attempts: 1

  ND reachable time is 30000 milliseconds

  ND advertised reachable time is 0 milliseconds

  ND advertised retransmit interval is 0 milliseconds

  ND router advertisements are sent every 200 seconds

  ND router advertisements live for 1800 seconds

  Hosts use stateless autoconfig for addresses.

Configuring Default Router Preference

Router advertisement messages are sent with the default router preference (DRP) configured by the 

ipv6 nd 

router-preference

 interface configuration command. If no DRP is configured, router advertisements are sent with a 

medium preference.

A DRP is useful when two routers on a link might provide equivalent, but not equal-cost routing, and policy might dictate 
that hosts should prefer one of the routers.

BEFORE YOU BEGIN

Complete the 

Configuring IPv6 Addressing and Enabling IPv6 Routing, page 934

.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

D-Link GO-RT-N300 Quick Installation Manual preview
GO-RT-N300
Brand: D-Link Pages: 32
D-Link DXN-W224 Quick Start Manual preview
DXN-W224
Brand: D-Link Pages: 6
D-Link DSR-250N User Manual preview
DSR-250N
Brand: D-Link Pages: 221
D-Link ShareCenter Pro DNS-1200-05 Quick Installation Manual preview
ShareCenter Pro DNS-1200-05
Brand: D-Link Pages: 68
D-Link Express Ethernetwork DI-707P Quick Installation Manual preview
Express Ethernetwork DI-707P
Brand: D-Link Pages: 14
National Instruments SCXI-1121 User Manual preview
SCXI-1121
Brand: National Instruments Pages: 162
Ubiquiti U5-24-500W Quick Start Manual preview
U5-24-500W
Brand: Ubiquiti Pages: 23
E-TOP BR486n User Manual preview
BR486n
Brand: E-TOP Pages: 76
Planet GSW-1602SF User Manual preview
GSW-1602SF
Brand: Planet Pages: 20
ADTRAN 617600026F1 Quick Start Manual preview
617600026F1
Brand: ADTRAN Pages: 9
ForeScout CounterACT Quick Installation Manual preview
CounterACT
Brand: ForeScout Pages: 28
Patton electronics 6103 User Manual preview
6103
Brand: Patton electronics Pages: 12
National Instruments NI WLS/ENET-9163 User Manual preview
NI WLS/ENET-9163
Brand: National Instruments Pages: 36
Campbell NL115 User Manual preview
NL115
Brand: Campbell Pages: 38
Compaq StorageWorks AIT 35GB AutoLoader Overview And Installation preview
StorageWorks AIT 35GB AutoLoader
Brand: Compaq Pages: 4
Orolia Seven Solutions WR-ZEN Series User Manual preview
Seven Solutions WR-ZEN Series
Brand: Orolia Pages: 167
Softing TH LINK Installation Manual preview
TH LINK
Brand: Softing Pages: 16
Zoom 4401F Specification Sheet preview
4401F
Brand: Zoom Pages: 2

Brands by name

Popular brands

Load more brands