manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

934

Configuring IPv6 Unicast Routing

 

Default Settings

Default Settings

Configuring IPv6

Configuring IPv6 Addressing and Enabling IPv6 Routing, page 934

Configuring Default Router Preference, page 937

Configuring IPv4 and IPv6 Protocol Stacks, page 938

Configuring DHCP for IPv6 Address Assignment, page 940

Configuring IPv6 ICMP Rate Limiting, page 943

Configuring CEF for IPv6, page 944

Configuring Static Routing for IPv6, page 944

Configuring RIP for IPv6, page 946

Configuring OSPF for IPv6, page 948

Configuring EIGRP for IPv6, page 950

Configuring BGP for IPv6, page 950

Configuring IPv6 Addressing and Enabling IPv6 Routing

To forward IPv6 traffic on an interface, you must configure a global IPv6 address on that interface. Configuring an IPv6 
address on an interface automatically configures a link-local address and activates IPv6 for the interface. The configured 
interface automatically joins these required multicast groups for that link:

solicited-node multicast group FF02:0:0:0:0:1:ff00::/104 for each unicast address assigned to the interface (the 
address for the neighbor discovery process)

all-nodes link-local multicast group FF02::1

all-routers link-local multicast group FF02::2

For more information about configuring IPv6 routing, see the “Implementing Addressing and Basic Connectivity for IPv6” 
chapter in the 

IPv6 Implementation Guide, Cisco IOS Release 15.2M&T

.

BEFORE YOU BEGIN

Be sure to select a dual IPv4 and IPv6 SDM template. 

Not all features discussed in this chapter are supported by the switch. See 

Unsupported IPv6 Unicast Routing 

Features, page 932

.

Feature

Default Setting

SDM template

Default.

IPv6 routing

Disabled globally and on all interfaces.

CEFv6

Disabled (IPv4 CEF is enabled by default).

Note: 

When IPv6 routing is enabled, CEFv6 is automatically enabled.

IPv6 addresses

None configured.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

H3C MSR 20-20 Supplementary Manual preview
MSR 20-20
Brand: H3C Pages: 6
3Com OfficeConnect 3CP4144 How To Set Up preview
OfficeConnect 3CP4144
Brand: 3Com Pages: 4
3Com OfficeConnect 3CP4144 Release Note preview
OfficeConnect 3CP4144
Brand: 3Com Pages: 2
H3C MSR 20-20 User Manual preview
MSR 20-20
Brand: H3C Pages: 60
H3C MSR 20 Series Manual preview
MSR 20 Series
Brand: H3C Pages: 149
3Com 3C13636 Installation Manual preview
3C13636
Brand: 3Com Pages: 27
3Com OfficeConnect 3C19500 User Manual preview
OfficeConnect 3C19500
Brand: 3Com Pages: 52
DBM ACE9600 Operating Manual preview
ACE9600
Brand: DBM Pages: 50
TP-Link L-R480T+ User Manual preview
L-R480T+
Brand: TP-Link Pages: 131
TP-Link TL-MR3620 Installation Manual preview
TL-MR3620
Brand: TP-Link Pages: 2
Handicare DX REM 420 User Manual preview
DX REM 420
Brand: Handicare Pages: 60
Zalip CDE570AM-U User Manual preview
CDE570AM-U
Brand: Zalip Pages: 76
Rosco ND100 User Manual preview
ND100
Brand: Rosco Pages: 20
ProSoft MVI46-PDPS User Manual preview
MVI46-PDPS
Brand: ProSoft Pages: 53
Teldat H2 RAIL Installation Manual preview
H2 RAIL
Brand: Teldat Pages: 47
Extreme Networks ACC-BKT-AX-BEAM Accessories Manual preview
ACC-BKT-AX-BEAM
Brand: Extreme Networks Pages: 35
Paradyne FrameSaver SLV NNI Installation Instructions Manual preview
FrameSaver SLV NNI
Brand: Paradyne Pages: 20
TP-Link VN020-F2v Quick Installation Manual preview
VN020-F2v
Brand: TP-Link Pages: 2

Brands by name

Popular brands

Load more brands