manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

950

Configuring IPv6 Unicast Routing

 

Configuring IPv6

To disable an OSPF routing process, use the no 

ipv6 router ospf

 

process-id 

global configuration command. To disable 

the OSPF routing process for an interface, use the 

no ipv6 ospf

 

process-id

 

area

 

area-id 

interface configuration 

command.

For more information about configuring OSPF routing for IPv6, see the “Implementing OSPF for IPv6” chapter in the 

IPv6 

Implementation Guide, Cisco IOS Release 15.2M&T

.

Configuring EIGRP for IPv6

By default, EIGRP for IPv6 is disabled. You can configure EIGRP for IPv6 on an interface. After configuring the router and 
the interface for EIGRP, enter the 

no shutdown

 privileged EXEC command to start EIGRP. 

Note: 

If EIGRP for IPv6 is not in shutdown mode, EIGRP might start running before you enter the EIRGP router-mode 

commands to configure the router and the interface.

To set an explicit router ID, use the 

show ipv6 eigrp 

command to see the configured router IDs, and then use the 

router-id

 command.

As with EIGRP IPv4, you can use EIGRPv6 to specify your EIGRP IPv4 interfaces and to select a subset of those as passive 
interfaces. Use the 

passive-interface default

 command to make all interfaces passive, and then use the 

no 

passive-interface

 command on selected interfaces to make them active. EIGRP IPv6 does not need to be configured 

on a passive interface.

For more configuration procedures, see the “Implementing EIGRP for IPv6” chapter in the 

IPv6 Implementation Guide, 

Cisco IOS Release 15.2M&T

.

Configuring BGP for IPv6

When configuring multiprotocol BGP extensions for IPv6, you must create the BGP routing process, configure peering 
relationships, and customize BGP for your particular network. Note that BGP functions the same in IPv6 as in IPv4. 

BEFORE YOU BEGIN

Before configuring the router to run BGP for IPv6, you must use the 

ipv6 unicast-routing

 command to globally enable 

IPv6 routing. 

8.

end

Return to privileged EXEC mode.

9.

show ipv6 ospf 

[

process-id

] [

area-id

] 

interface

 [

interface-id

]

or

show ipv6 ospf 

[

process-id

] [

area-id

] 

Display information about OSPF interfaces.

Display general information about OSPF routing 
processes.

10.

copy running-config startup-config

 

(Optional) Save your entries in the configuration file.

Command

Purpose

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

Panasonic KX-HTS Series Quick Start Manual preview
KX-HTS Series
Brand: Panasonic Pages: 2
D-Link DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network... User Manual preview
DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network...
Brand: D-Link Pages: 53
Queclink GV600 Series Instruction Manual preview
GV600 Series
Brand: Queclink Pages: 9
STONEFLY DR365V-2404 Setup Manual preview
DR365V-2404
Brand: STONEFLY Pages: 48
Z Microsystems TranzStor 8X User Manual preview
TranzStor 8X
Brand: Z Microsystems Pages: 51
BWI PCI Duo/TP User Manual preview
PCI Duo/TP
Brand: BWI Pages: 5
i-MO OptiBond 210 C Series Hardware Installation Manual preview
OptiBond 210 C Series
Brand: i-MO Pages: 16
Olicom Ethernet MCA 10/100 Adapter Manual To Operations preview
Ethernet MCA 10/100 Adapter
Brand: Olicom Pages: 88
Extron electronics Network Adapter AC AAP Specifications preview
Network Adapter AC AAP
Brand: Extron electronics Pages: 2
RouterBOARD Groove A-52HPn Quick Setup Manual preview
Groove A-52HPn
Brand: RouterBOARD Pages: 4
AIC FB128-LX User Manual preview
FB128-LX
Brand: AIC Pages: 79
Multitech RouteFinder RF560VPN User Manual preview
RouteFinder RF560VPN
Brand: Multitech Pages: 82
Yeti 20731 Quick Start Manual preview
20731
Brand: Yeti Pages: 29
Alcatel OmniSwitch 6624 Network Configuration Manual preview
OmniSwitch 6624
Brand: Alcatel Pages: 546
Lancom 1711+ VPN Manual preview
1711+ VPN
Brand: Lancom Pages: 79
Billion Modem/Router ADSL BIPAC-7100 (Italian) Guida Rapida preview
Modem/Router ADSL BIPAC-7100
Brand: Billion Pages: 13
Crestron 8 Channel Dimmer Module CLX-1DIM8 Specification Sheet preview
8 Channel Dimmer Module CLX-1DIM8
Brand: Crestron Pages: 1
Carotron C10032-000 Instruction Manual preview
C10032-000
Brand: Carotron Pages: 10

Brands by name

Popular brands

Load more brands