manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

813

   

Configuring IP Unicast Routing

Configuring IP Addressing

Switch(config)# 

ip forward-protocol udp 

Switch(config)# 

end

Establishing an IP Broadcast Address

The most popular IP broadcast address (and the default) is an address consisting of all ones (255.255.255.255). 
However, the switch can be configured to generate any form of IP broadcast address.

DETAILED STEPS

To restore the default IP broadcast address, use the 

no ip broadcast-address

 interface configuration command.

EXAMPLE

The following example specifies an IP broadcast address of 0.0.0.0: 

Switch# 

configure terminal 

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)# 

interface ethernet 0

Switch(config-if)# 

ip broadcast-address 0.0.0.0

Switch(config-if)# 

end

Flooding IP Broadcasts

You can allow IP broadcasts to be flooded throughout your internetwork in a controlled fashion by using the database 
created by the bridging STP. Using this feature also prevents loops. To support this capability, bridging must be 
configured on each interface that is to participate in the flooding. If bridging is not configured on an interface, the 
interface can receive broadcasts but it never forwards the broadcasts it receives, and the router never uses that interface 
to send broadcasts received on a different interface.

Packets that are forwarded to a single network address using the IP helper-address mechanism can be flooded. Only 
one copy of the packet is sent on each network segment. 

To be considered for flooding, packets must meet these criteria. (Note that these are the same conditions used to 
consider packet forwarding using IP helper addresses.)

The packet must be a MAC-level broadcast.

The packet must be an IP-level broadcast.

Command

Purpose

1.

configure terminal

Enter global configuration mode.

2.

interface

 

interface-id

Enter interface configuration mode, and specify the 
interface to configure.

3.

no shutdown

 

Enable the interface if necessary. By default, UNIs and 
ENIs are disabled and NNIs are enabled. 

4.

ip broadcast-address 

ip-address

Enter a broadcast address different from the default, for 
example 128.1.255.255.

5.

end

 

Return to privileged EXEC mode.

6.

show ip interface

 [

interface-id

]

Verify the broadcast address on the interface or all 
interfaces.

7.

copy running-config startup-config

 

(Optional) Save your entries in the configuration file.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

ABB RELION REF615R Manual preview
RELION REF615R
Brand: ABB Pages: 66
D-Link DSL-500 Command Reference Manual preview
DSL-500
Brand: D-Link Pages: 15
D-Link DSN-4100 Series Quick Start Manual preview
DSN-4100 Series
Brand: D-Link Pages: 2
D-Link DWL-G550 Product Data Sheet preview
DWL-G550
Brand: D-Link Pages: 2
H3C RA100 Installation Manual preview
RA100
Brand: H3C Pages: 34
Keithley 7707 User Manual preview
7707
Brand: Keithley Pages: 59
N-Tron 7018 User Manual & Installation Manual preview
7018
Brand: N-Tron Pages: 138
Konig CMP-HOMEPL1000 Manual preview
CMP-HOMEPL1000
Brand: Konig Pages: 73
Delta Electronics Ethernet Communication Module DVPEN01-SL Manual preview
Ethernet Communication Module DVPEN01-SL
Brand: Delta Electronics Pages: 54
Enginko MCF-LW06424 Operating Manual preview
MCF-LW06424
Brand: Enginko Pages: 19
Allied Telesis AR725 Quick Start Manual preview
AR725
Brand: Allied Telesis Pages: 22
Variscite VAR-EXT-CB105 Datasheet preview
VAR-EXT-CB105
Brand: Variscite Pages: 18
UfiSpace S9700-23D Hardware Installation Manual preview
S9700-23D
Brand: UfiSpace Pages: 32
Galaxy Hunter Series Quick Start Manual preview
Hunter Series
Brand: Galaxy Pages: 30
Asante IntraCore 6524 User Manual preview
IntraCore 6524
Brand: Asante Pages: 150
Kramer RK-10MT Quick Start Manual preview
RK-10MT
Brand: Kramer Pages: 2
Trend Micro IPS Pro-Module-24C-GE-BP-TM Quick Setup Manual preview
IPS Pro-Module-24C-GE-BP-TM
Brand: Trend Micro Pages: 3
Accton Technology MR3202A User Manual preview
MR3202A
Brand: Accton Technology Pages: 78

Brands by name

Popular brands

Load more brands