Cisco IE 4000 Software Configuration Manual Download Page 223

Page: 223 / 1066

219

Configuring IEEE 802.1x Port-Based Authentication

How to Configure IEEE 802.1x Port-Based Authentication

Configuring the Switch-to-RADIUS-Server Communication

You can globally configure the timeout, retransmission, and encryption key values for all RADIUS servers by using the

radius-server host

global configuration command. If you want to configure these options on a per-server basis, use the

radius-server timeout

radius-server retransmit

, and the

radius-server key

global configuration commands. For more

information, see

Configuring Settings for All RADIUS Servers, page 176

aaa authorization network

{

default

}

group radius

(Optional) Configures the switch to use user-RADIUS authorization for all
network-related service requests, such as per-user ACLs or VLAN
assignment.

For per-user ACLs, single-host mode must be configured. This setting is
the default.

radius-server host

ip-address

(Optional) Specifies the IP address of the RADIUS server.

radius-server key

string

(Optional) Specifies the authentication and encryption key used between
the switch and the RADIUS daemon running on the RADIUS server.

interface

interface-id

Specifies the port connected to the client to enable for 802.1x
authentication, and enter interface configuration mode.

switchport mode access

(Optional) Sets the port to access mode only if you configured the
RADIUS server in Step 6 and Step 7.

10.

authentication port-control auto

Enables 802.1x authentication on the port.

11.

dot1x pae authenticator

Sets the interface Port Access Entity to act only as an authenticator and
ignore messages meant for a supplicant.

12.

end

Returns to privileged EXEC mode.

13.

show authentication

Verifies your entries.

14.

copy running-config startup-config

(Optional) Saves your entries in the configuration file.

Command

Purpose

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IE 4000

Reviews:

Related manuals for IE 4000

Brands by name

Popular brands

Cisco IE 4000, Software Configuration Manual

Search results

Summary of Contents for IE 4000

Reviews:

Related manuals for IE 4000

Brands by name

Popular brands