747
Configuring MSDP
Configuring MSDP
To remove the filter, use the
no
ip msdp sa-filter in
{
ip-address
|
name
} [
list
access-list-number
] [
route-map
map-tag
]
global configuration command.
EXAMPLE
This example shows how to filter all SA messages from the peer named
switch.cisco.com
:
Switch(config)#
ip msdp peer switch.cisco.com connect-source gigabitethernet0/1
Switch(config)#
ip msdp sa-filter in switch.cisco.com
Configuring an MSDP Mesh Group
An MSDP mesh group is a group of MSDP speakers that have fully meshed MSDP connectivity among one another. Any
SA messages received from a peer in a mesh group are not forwarded to other peers in the same mesh group. Thus, you
reduce SA message flooding and simplify peer-RPF flooding. Use the
ip msdp mesh-group
global configuration
command when there are multiple RPs within a domain. It is especially used to send SA messages across a domain. You
can configure multiple mesh groups (with different names) in a single switch. This procedure is optional.
DETAILED STEPS
To remove an MSDP peer from a mesh group, use the
no
ip msdp mesh-group
name
{
ip-address
|
name
} global
configuration command.
EXAMPLE
The following example shows how to configure the MSDP peer at address 192.168.1.3 to be a member of the mesh
group named internal:
Switch(config)#
ip msdp mesh-group internal 192.168.1.3
Table 0-8
Command
Purpose
1.
configure terminal
Enter global configuration mode.
2.
ip msdp mesh-group
name
{
ip-address
|
name
}
Configure an MSDP mesh group, and specify the MSDP peer
belonging to that mesh group.
By default, the MSDP peers do not belong to a mesh group.
For
name
, enter the name of the mesh group.
For
ip-address
|
name
, enter the IP address or name of the
MSDP peer to be a member of the mesh group.
3.
end
Return to privileged EXEC mode.
4.
show running-config
Verify your entries.
5.
copy running-config
startup-config
(Optional) Save your entries in the configuration file.
6.
Repeat this procedure on each MSDP peer in the group.
Summary of Contents for IE 4000
