manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

460

Configuring Port-Based Traffic Control

 

How to Configure Port-Based Traffic Control

Configuring Protocol Storm Protection

Enabling Protocol Storm Protection

2.

interface 

interface-id

Specifies the interface to be configured, and enters 
interface configuration mode.

3.

switchport port-security

 

aging

 {

static | time

 

time

 | 

type 

{

absolute | inactivity}

}

Enables or disables static aging for the secure port, or sets 
the aging time or type.

Note: 

The switch does not support port security aging of 

sticky secure addresses.

static

—Enables aging for statically configured secure 

addresses on this port.

time

—Specifies the aging time for this port. The valid range 

is from 0 to 1440 minutes.

type

—Specifies the aging type as either absolute or 

inactivity.

absolute

—All the secure addresses on this port age out 

exactly after the

 

time

 (

minutes) specified lapses and are 

removed from the secure address list.

inactivity

—The secure addresses on this port age out 

only if there is no data traffic from the secure source 
addresses for the specified time period.

4.

end

Returns to privileged EXEC mode.

Command

Purpose

Command

Purpose

1.

configure terminal

Enters global configuration mode.

2.

psp

 {

arp

 | 

dhcp

 | 

igmp

} 

pps

 

value

Configures protocol storm protection for ARP, IGMP, or DHCP.

value

—Specifies the threshold value for the number of packets per 

second. If the traffic exceeds this value, protocol storm protection 
is enforced. The range is from 5 to 50 packets per second.

3.

errdisable detect cause psp

(Optional) Enables error-disable detection for protocol storm 
protection. If this feature is enabled, the virtual port is 
error-disabled. If this feature is disabled, the port drops excess 
packets without error-disabling the port.

4.

errdisable recovery interval

 

time

(Optional) Configures an auto-recovery time (in seconds) for 
error-disabled virtual ports. When a virtual port is error-disabled, 
the switch auto-recovers after this time. The range is from 30 to 
86400 seconds. 

5.

end

Returns to privileged EXEC mode.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

Patton electronics 3210 Specification Sheet preview
3210
Brand: Patton electronics Pages: 2
Paradyne MCC Installation Instructions Manual preview
MCC
Brand: Paradyne Pages: 11
Paradyne Hotwire 8784 Installation Instructions Manual preview
Hotwire 8784
Brand: Paradyne Pages: 19
Paradyne Hotwire 7995 Installation Instructions Manual preview
Hotwire 7995
Brand: Paradyne Pages: 32
Paradyne COMSPHERE 3550 Series User Manual preview
COMSPHERE 3550 Series
Brand: Paradyne Pages: 153
Paradyne Jetstream CPX-1000 Reference Manual preview
Jetstream CPX-1000
Brand: Paradyne Pages: 141
Paradyne FrameSaver 9783 Installation Instructions Manual preview
FrameSaver 9783
Brand: Paradyne Pages: 28
Paradyne COMSPHERE 6800 Series Installation And Enabling/Disabling Instructions preview
COMSPHERE 6800 Series
Brand: Paradyne Pages: 7
Konica Minolta Network Setup Network Setup Manual preview
Network Setup
Brand: Konica Minolta Pages: 38
Western Digital My Net N750 Start Here Manual preview
My Net N750
Brand: Western Digital Pages: 8
Tbus NV-ER1816i Installation Manual preview
NV-ER1816i
Brand: Tbus Pages: 25
Faderfox 4midiloop User Manual preview
4midiloop
Brand: Faderfox Pages: 10
Paradyne 7510 DSU Start-Up Instructions preview
7510 DSU
Brand: Paradyne Pages: 10
XtendLan NVR-xUD User Manual preview
NVR-xUD
Brand: XtendLan Pages: 228
ActionTec MI424WR MI424WR Upgrade Procedure preview
MI424WR
Brand: ActionTec MI424WR Pages: 3
Erbauer 3663602796282 Original Instructions Manual preview
3663602796282
Brand: Erbauer Pages: 36
Planet FGSW-2620PVS User Manual preview
FGSW-2620PVS
Brand: Planet Pages: 67
Cambium Networks PMP/PTP 450 Series Quick Start Manual preview
PMP/PTP 450 Series
Brand: Cambium Networks Pages: 155

Brands by name

Popular brands

Load more brands