Cisco IE 4000 Software Configuration Manual Download Page 1017 | Manualshive

Page: 1017 / 1066

background image

1013

Working with the Cisco IOS File System, Configuration Files, and Software Images

Working with Software Images

Working with Software Images

This section describes how to archive (download and upload) software image files, which contain the system software,
the Cisco IOS code, and the embedded Device Manager software.

Note:

Instead of using the

copy

privileged EXEC command or the

archive tar

privileged EXEC command, we recommend

using the

archive download-sw

and

archive upload-sw

privileged EXEC commands to download and upload software

image files.

You can download a switch image file from a TFTP, FTP, or RCP server to upgrade the switch software. If you do not have
access to a TFTP server, you can download a software image file directly to your PC or workstation by using a web
browser (HTTP) and then by using Device Manager or Cisco Network Assistant to upgrade your switch. For information
about upgrading your switch by using a TFTP server or a web browser (HTTP), see the release notes.

You can replace the current image with the new one or keep the current image in flash memory after a download.

You upload a switch image file to a TFTP, FTP, or RCP server for backup purposes. You can use this uploaded image for
future downloads to the same switch or to another of the same type.

5.

configure replace

target-url

[

list

]

[

force

] [

time

seconds

] [

nolock

]

Replaces the running configuration file with a saved configuration file.

target-url—

URL (accessible by the file system) of the saved configuration file

that is to replace the running configuration, such as the configuration file
created in Step 2 by using the

archive config

privileged EXEC command.

list

—

Displays a list of the command entries applied by the software parser

during each pass of the configuration replacement operation. The total number
of passes also appears.

force

—

Replaces the running configuration file with the specified saved

configuration file without prompting you for confirmation.

time

seconds—

Specifies the time (in seconds) within which you must enter the

configure confirm

command to confirm replacement of the running

configuration file. If you do not enter the

configure confirm

command within

the specified time limit, the configuration replacement operation is
automatically stopped. (In other words, the running configuration file is
restored to the configuration that existed before you entered the

configure

replace

command).

Note:

You must first enable the configuration archive before you can use the

time

seconds

command line option.

nolock

—

Disables the locking of the running configuration file that prevents

other users from changing the running configuration during a configuration
replacement operation.

6.

configure confirm

(Optional) Confirms replacement of the running configuration with a saved
configuration file.

Note:

Use this command only if the

time

seconds

keyword and argument of

the

configure replace

command are specified

.

7.

copy running-config
startup-config

(Optional) Saves your entries in the configuration file.

Command

Purpose

«
...
1015
1016
1017
1018
1019
...
»

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

BB-HGW700A - Network Camera Router

Brand: Panasonic Pages: 10

Netlink FRX8000

Brand: Cabletron Systems Pages: 94

MMAC-Plus 9E423-24

Brand: Cabletron Systems Pages: 10

MMAC-Plus 9A128-01

Brand: Cabletron Systems Pages: 22

Spectrum EMM-E6

Brand: Cabletron Systems Pages: 2

SmartSTACK ELS100-24TXG

Brand: Cabletron Systems Pages: 112

Brand: Cabletron Systems Pages: 86

Brand: Cabletron Systems Pages: 54

Cabletron BRIM-F6

Brand: Cabletron Systems Pages: 43

Netlink FRX4000

Brand: Cabletron Systems Pages: 60

CSX200 CyberSWITCH

Brand: Cabletron Systems Pages: 2

Brand: Cabletron Systems Pages: 8

Brand: Cabletron Systems Pages: 4

Dimension ES-3124

Brand: ZyXEL Communications Pages: 228

Anybus Communicator ABC4021

Brand: HMS Networks Pages: 60

TRAK 2OP M11 Mill

Brand: XYZ Machine Tools Pages: 203

Brand: Comet Labs Pages: 11

Brand: UNICORECOMM Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands