manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

893

   

Configuring IP Unicast Routing

Configuring BFD

DETAILED STEPS

To disable HSRP support for BFD on all interfaces, enter the 

no standby bfd all-interfaces

 global configuration 

command. To disable it on an interface, enter the 

no standby bfd

 interface configuration command.

Note: 

If you disable standby BFD on an interface by entering the 

no standby bfd 

interface configuration command, to 

activate BFD sessions on other interfaces, you must disable and reenable it globally by entering the 

no standby bfd 

all-interfaces 

global configuration command followed by the 

standby bfd all-interfaces

 global configuration command.

EXAMPLE

The following example shows how to reenable HSRP BFD peering if it has been disabled on a switch: 

Switch(config)# 

standby bfd all-interfaces

Disabling BFD Echo Mode

When you configure a BFD session, BFD echo mode is enabled by default on BFD interfaces. You can disable echo mode 
on an interface so it sends no echo packets and but only sends back echo packets received from a neighbor. When echo 
mode is disabled, control packets are used to detect forwarding failures. You can configure slow timers to reduce the 
frequency of BFD control packets. 

BEFORE YOU BEGIN

Configure BFD parameters on the interface as described in the 

Configuring BFD Session Parameters on an Interface, 

page 886

.

Command

Purpose

1.

configure terminal

Enter global configuration mode.

2.

interface

 

interface-id 

Specify an interface for a BFD session, and enter interface 
configuration mode. Only physical interfaces support BFD.

3.

ip address

 

ip-address

 

subnet-mask

 

Configure the IP address and IP subnet mask for the interface.

4.

standby 

[

group-number

]

 

ip 

[

ip-address

] [

secondary

]] 

Activate HSRP. 

5.

standby bfd

(Optional) Enable HSRP support for BFD on the interface.

6.

exit

Return to global configuration mode.

7.

standby bfd all-interfaces

(Optional) Enable HSRP support for BFD on all interfaces.

8.

end

 

Return to privileged EXEC mode.

9.

show standby neighbors

Verify your entries. 

10.

copy running-config 
startup-config

 

(Optional) Save your entries in the configuration file.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

Habitat M10 Installation Manual preview
M10
Brand: Habitat Pages: 48
MikroTik RouterBOARD SXT 5HnD Quick Setup Manual And Warranty Information preview
RouterBOARD SXT 5HnD
Brand: MikroTik Pages: 2
AMX NXA-ENET8POE Installation Manual preview
NXA-ENET8POE
Brand: AMX Pages: 2
JUMO 705041 Installation Instructions Manual preview
705041
Brand: JUMO Pages: 60
VCS VIP 1000 User Manual preview
VIP 1000
Brand: VCS Pages: 118
Observint NVR16 Firmware User Manual preview
NVR16
Brand: Observint Pages: 117
Weidmuller IE-SW-PL09M-5GC-4GT Hardware Installation Manual preview
IE-SW-PL09M-5GC-4GT
Brand: Weidmuller Pages: 15
ADTRAN NetVanta Serial Dial Backup Interface Module (DIM) none Quick Start Manual preview
NetVanta Serial Dial Backup Interface Module (DIM) none
Brand: ADTRAN Pages: 2
JLCooper Electronics GangWay32 User Manual preview
GangWay32
Brand: JLCooper Electronics Pages: 12
Idis DR-8364F Quick Manual preview
DR-8364F
Brand: Idis Pages: 16
N-Tron 900B Installation & User Manual preview
900B
Brand: N-Tron Pages: 21
MTI BR5811 User Manual preview
BR5811
Brand: MTI Pages: 41
Digi Digi Connect WAN Application Manual preview
Digi Connect WAN
Brand: Digi Pages: 3
Digi CR4110 Installation Manual preview
CR4110
Brand: Digi Pages: 13
Digi TransPort WR11 XT Quick Start Manual preview
TransPort WR11 XT
Brand: Digi Pages: 4
SOYO AVRO3001 User Manual preview
AVRO3001
Brand: SOYO Pages: 40
Panasonic PN28160A Operation Manual preview
PN28160A
Brand: Panasonic Pages: 277
Panasonic PN28480K-ID Operation Manual preview
PN28480K-ID
Brand: Panasonic Pages: 438

Brands by name

Popular brands

Load more brands