manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

886

Configuring IP Unicast Routing

 

Configuring BFD

When using BFD echo mode (the default), you should disable sending of ICMP redirect messages by entering the 

no ip 

redirects 

interface configuration command on the BFD interface. 

Configuring BFD Session Parameters on an Interface

Before you can start a BFD session on an interface, you must put the interface into Layer 3 mode and set the baseline 
BFD parameters on it. 

Note: 

Although you can configure BFD on Layer 2 interfaces, a BFD session cannot start until both interfaces are in Layer 

3 mode and routing is enabled on the switch.

BEFORE YOU BEGIN

See 

Default BFD Configuration Guidelines, page 885

.

DETAILED STEPS

To remove the BFD parameter configuration, enter the

 no bfd interval

 interface configuration command. 

Command

Purpose

1.

configure terminal

Enter global configuration mode.

2.

interface

 

interface-id 

Specify an interface for a BFD session, and enter interface 
configuration mode. Only physical interfaces support BFD.

3.

no shutdown

 

Enable the interface if necessary. User network interfaces (UNIs) 
and enhanced network interfaces (ENIs) are disabled by default; 
network node interfaces (NNIs) are enabled by default. 

4.

no switchport

Remove the interface from Layer 2 configuration mode.

5.

ip address

 

ip-address

 

subnet-mask

 

Configure the IP address and IP subnet mask.

6.

bfd interval 

milliseconds 

min_rx 

milliseconds 

multiplier 

value

Set BFD parameters for echo packets on the interface. 

interval

—Specify the rate at which BFD echo packets are sent 

to BFD peers. The range is from 50 to 999 milliseconds (ms). 

min_rx

—Specify the rate at which BFD echo packets are 

expected to be received from BFD peers. The range is from 
50 to 999 ms.

multiplier

—Specify the number of consecutive BFD echo 

packets that must be missed from a BFD peer before BFD 
declares that it is unavailable and informs the other BFD peer 
of the failure. The range is from 3 to 50. 

Note: 

There are no baseline BFD parameter defaults.

7.

end

 

Return to privileged EXEC mode.

8.

show running-config

Verify your entries. 

9.

show bfd neighbor detail

(Optional) Display the final configured or negotiated values when 
the session is created with a neighbor.

10.

copy running-config 
startup-config

 

(Optional) Save your entries in the configuration file.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

ICP DAS USA ZT-2510 Series Quick Start Manual preview
ZT-2510 Series
Brand: ICP DAS USA Pages: 8
LaCie 8BIG RACK THUNDERBOLT 2 Quick Start Manual preview
8BIG RACK THUNDERBOLT 2
Brand: LaCie Pages: 28
Q-See QC814 Specifications preview
QC814
Brand: Q-See Pages: 2
iBall Baton 150m Configuration Manual preview
150m
Brand: iBall Baton Pages: 9
RuggedCom RUGGEDMAX WIN7000 Installation Manual preview
RUGGEDMAX WIN7000
Brand: RuggedCom Pages: 42
SMC Networks Barricade SMC7901WBRA2 Installation Manual preview
Barricade SMC7901WBRA2
Brand: SMC Networks Pages: 2
ZyXEL Communications XGS4700 Series Manual preview
XGS4700 Series
Brand: ZyXEL Communications Pages: 485
ZyXEL Communications P-974H - V3.70 Manual preview
P-974H - V3.70
Brand: ZyXEL Communications Pages: 116
Telex Communications 2472AA Instruction Manual preview
2472AA
Brand: Telex Communications Pages: 28
XtendLan NVR-xUD User Manual preview
NVR-xUD
Brand: XtendLan Pages: 228
Eneo PNR-5304 Quick Installation Manual preview
PNR-5304
Brand: Eneo Pages: 68
E-LINX EIR410-2SFP-T User Manual preview
EIR410-2SFP-T
Brand: E-LINX Pages: 24
Z-Wave RAZBERRY 7 PRO Quick Start Manual preview
RAZBERRY 7 PRO
Brand: Z-Wave Pages: 6
ICP DAS USA iWSN-200E Quick Start Manual preview
iWSN-200E
Brand: ICP DAS USA Pages: 8
Accton Technology MR3202A User Manual preview
MR3202A
Brand: Accton Technology Pages: 78
ALIBI ALI-NVR71128R User Manual preview
ALI-NVR71128R
Brand: ALIBI Pages: 232
FiberHome AN5506-04-B User Manual preview
AN5506-04-B
Brand: FiberHome Pages: 44
Aaeon FWS-7811 Manual preview
FWS-7811
Brand: Aaeon Pages: 100

Brands by name

Popular brands

Load more brands