manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

241

Cisco Systems, Inc.

www.cisco.com

 

Configuring Web-Based Authentication

Prerequisites for Configuring 

Web-Based Authentication

 

By default, the IP device tracking feature is disabled on a switch. You must enable the IP device tracking feature to 
use web-based authentication.

You must configure at least one IP address to run the switch HTTP server. You must also configure routes to reach 
each host IP address. The HTTP server sends the HTTP login page to the host.

You must configure the default ACL on the interface before configuring web-based authentication. Configure a port 
ACL for a Layer 2 interface.

Restrictions for Configuring 

Web-Based Authentication

Web-based authentication is an ingress-only feature.

You can configure web-based authentication only on access ports. Web-based authentication is not supported on 
trunk ports, EtherChannel member ports, or dynamic trunk ports.

You cannot authenticate hosts on Layer 2 interfaces with static ARP cache assignment. These hosts are not detected 
by the web-based authentication feature because they do not send ARP messages.

Hosts that are more than one hop away might experience traffic disruption if an STP topology change results in the 
host traffic arriving on a different port. This occurs because the ARP and DHCP updates might not be sent after a 
Layer 2 (STP) topology change.

Web-based authentication does not support VLAN assignment as a downloadable-host policy.

Web-based authentication is not supported for IPv6 traffic.

Web-based authentication and Network Edge Access Topology (NEAT) are mutually exclusive. You cannot use 
web-based authentication when NEAT is enabled on an interface, and you cannot use NEAT when web-based 
authentication is running on an interface.

Web-based authentication supports only RADIUS authorization servers. You cannot use servers or local 
authorization.

Information About Configuring 

Web-Based Authentication 

Web-Based Authentication

Use the web-based authentication feature, known as 

web authentication proxy

, to authenticate end users on host 

systems that do not run the IEEE 802.1x supplicant.

Note: 

You can configure web-based authentication on Layer 2 interfaces.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

D-Link DSL-2750U Setup preview
DSL-2750U
Brand: D-Link Pages: 14
D-Link DVG-7022S Quick Installation Manual preview
DVG-7022S
Brand: D-Link Pages: 7
D-Link DIR-878 Quick Installation Manual preview
DIR-878
Brand: D-Link Pages: 41
Grasslin TOWERCHRON DP72 Programming Manual preview
TOWERCHRON DP72
Brand: Grasslin Pages: 2
3Com 3C410012A - OfficeConnect Remote 531 Access... Getting Started Manual preview
3C410012A - OfficeConnect Remote 531 Access...
Brand: 3Com Pages: 72
impinj Speedway Revolution Installation And Operation Manual preview
Speedway Revolution
Brand: impinj Pages: 60
QNAP Turbo NAS TVS-71 Series Hardware User Manual preview
Turbo NAS TVS-71 Series
Brand: QNAP Pages: 51
LaCie 301300U - Ethernet Disk NAS Server User Manual preview
301300U - Ethernet Disk NAS Server
Brand: LaCie Pages: 62
AMX AXB-PSCV Dimensional Drawing preview
AXB-PSCV
Brand: AMX Pages: 1
Pakedge Device & Software RK-1 Quick Start Manual preview
RK-1
Brand: Pakedge Device & Software Pages: 14
QTech QSW-2900 User Manual preview
QSW-2900
Brand: QTech Pages: 406
Fluke Network Tester User Manual preview
Network Tester
Brand: Fluke Pages: 102
3Com Fast EtherLink XL PCI 10/100BASE-TXNetwork Interface... Quick Manual preview
Fast EtherLink XL PCI 10/100BASE-TXNetwork Interface...
Brand: 3Com Pages: 12
Nexxt Amp300 Quick Installation Manual preview
Amp300
Brand: Nexxt Pages: 2
Acces PCI-COM-1S User Manual preview
PCI-COM-1S
Brand: Acces Pages: 21
Hame 434T User Manual preview
434T
Brand: Hame Pages: 37
Aztech na8300 Easy Start preview
na8300
Brand: Aztech Pages: 13
G&D DP1.2-Vision-IP-Fiber Installation And Operation Manual preview
DP1.2-Vision-IP-Fiber
Brand: G&D Pages: 240

Brands by name

Popular brands

Load more brands