manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

663

   

Configuring IPv6 Host Functions

How to Configure IPv6 Hosting

Configuring Default Router Preference

Router advertisement messages are sent with the default router preference (DRP) configured by the 

ipv6 nd 

router-preference

 interface configuration command. If no DRP is configured, RAs are sent with a medium preference.

A DRP is useful when two routers on a link might provide equivalent, but not equal-cost routing, and policy might dictate 
that hosts should prefer one of the routers.

Configuring IPv6 ICMP Rate Limiting

ICMP rate limiting is enabled by default with a default interval between error messages of 100 milliseconds and a bucket 
size (maximum number of tokens to be stored in a bucket) of 10. 

7.

ipv6 address

 

ipv6-prefix/prefix

 

length 

eui-64

or

ipv6 address

 

ipv6-address 

link-local

or

ipv6 enable

Specifies a global IPv6 address with an extended unique 
identifier (EUI) in the low-order 64 bits of the IPv6 address.

Specifies only the network prefix; the last 64 bits are 
automatically computed from the switch MAC address. This 
enables IPv6 processing on the interface.

Specifies a link-local address on the interface to be used 
instead of the link-local address that is automatically 
configured when IPv6 is enabled on the interface. This 
command enables IPv6 processing on the interface.

Automatically configures an IPv6 link-local address on the 
interface, and enable the interface for IPv6 processing. The 
link-local address can only be used to communicate with 
nodes on the same link.

8.

exit

Returns to global configuration mode.

9.

end

Returns to privileged EXEC mode.

Command

Purpose

Command

Purpose

1.

configure terminal

Enters global configuration mode.

2.

interface

 

interface-id

Enters interface configuration mode, and enters the Layer 3 interface 
on which you want to specify the DRP.

3.

ipv6 nd router-preference 

{

high

 | 

medium | low

}

Specifies a DRP for the router on the switch interface.

4.

end

Returns to privileged EXEC mode.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

Hama 53107 Operating Instruction preview
53107
Brand: Hama Pages: 10
Hornington AirStation WHR-G300N Settings preview
AirStation WHR-G300N
Brand: Hornington Pages: 6
EVOC 6336-STG-YX Manual preview
6336-STG-YX
Brand: EVOC Pages: 57
TP-Link TL-MR3220 Quick Installation Manual preview
TL-MR3220
Brand: TP-Link Pages: 87
Paradyne ACCULINK 3161 CSU Quick Reference Manual preview
ACCULINK 3161 CSU
Brand: Paradyne Pages: 19
Hypercom IN-tact 1201 Brochure & Specs preview
IN-tact 1201
Brand: Hypercom Pages: 2
H3C WT2024-U-PWR Compliance And Safety Manual preview
WT2024-U-PWR
Brand: H3C Pages: 51
NETGEAR DG834GUV5 User Manual preview
DG834GUV5
Brand: NETGEAR Pages: 120
SMC Networks EZ Switch SMC-1026DT V.2 User Manual preview
EZ Switch SMC-1026DT V.2
Brand: SMC Networks Pages: 27
e+p OCH 110 Installation Manual preview
OCH 110
Brand: e+p Pages: 2
ratiotec CONNECT Box Pro Instruction Manual preview
CONNECT Box Pro
Brand: ratiotec Pages: 12
Waveshare 5G CPE BOX User Manual preview
5G CPE BOX
Brand: Waveshare Pages: 27
Waveshare OPS-I5-1135G7 User Manual preview
OPS-I5-1135G7
Brand: Waveshare Pages: 23
Ecos SECURE BOOT STICK FX Administrator'S Manual preview
SECURE BOOT STICK FX
Brand: Ecos Pages: 22
Costar CDC2500LX User Manual preview
CDC2500LX
Brand: Costar Pages: 51
Infrant Technologies ReadyNAS NV Getting Started Manual preview
ReadyNAS NV
Brand: Infrant Technologies Pages: 8
Crestron DM-TX-200-C-2G Operations & Installation Manual preview
DM-TX-200-C-2G
Brand: Crestron Pages: 36
Viking FXI-1 Product Manual preview
FXI-1
Brand: Viking Pages: 8

Brands by name

Popular brands

Load more brands