manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

72

Performing Switch Setup Configuration

 

How to Perform Switch Setup Configuration

Modifying the Startup Configuration

Specifying the Filename to Read and Write the System Configuration

By default, the Cisco IOS software uses the 

config.text

 file to read and write a nonvolatile copy of the system 

configuration. However, you can specify a different filename, which will be loaded during the next boot-up cycle.

Manually Booting the Switch

By default, the switch automatically boots up; however, you can configure it to manually boot up.

Before You Begin

Use a standalone switch for this task.

5.

ip default-gateway

 

ip-address

Enters the IP address of the next-hop router interface that is directly 
connected to the switch where a default gateway is being configured. 
The default gateway receives IP packets with unresolved destination IP 
addresses from the switch.

Once the default gateway is configured, the switch has connectivity to 
the remote networks with which a host needs to communicate.

Note: 

When your switch is configured to route with IP, it does not need to 

have a default gateway set.

6.

end

Returns to privileged EXEC mode.

7.

show interfaces vlan

 

vlan-id

 

Verifies the configured IP address.

8.

show ip redirects

Verifies the configured default gateway. 

9.

copy running-config startup-config

(Optional) Saves your entries in the configuration file.

Command

Purpose

Command

Purpose

1.

configure terminal

Enters global configuration mode.

2.

boot config-file flash:/

file-url

Specifies the configuration file to load during the next boot-up 
cycle.

For 

file-url

, specify the path (directory) and the configuration 

filename.

Filenames and directory names are case sensitive.

3.

end

Returns to privileged EXEC mode.

4.

show boot

Verifies your entries.

The 

boot config-file

 global configuration command changes the 

setting of the CONFIG_FILE environment variable.

5.

copy running-config startup-config

(Optional) Saves your entries in the configuration file.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

M2M Pro User Manual (Extract preview
Pro
Brand: M2M Pages: 9
Icidu NI-707533 Manual Manual preview
NI-707533
Brand: Icidu Pages: 10
Patton electronics SMARTNODE 4900 Getting Started Manual preview
SMARTNODE 4900
Brand: Patton electronics Pages: 75
Patton electronics RocketLink-G 3088/I Getting Started Manual preview
RocketLink-G 3088/I
Brand: Patton electronics Pages: 61
Patton SmartNode 5200 Quick Start Manual preview
SmartNode 5200
Brand: Patton Pages: 12
Patton SL4020 Getting Started Manual preview
SL4020
Brand: Patton Pages: 84
Patton OnSite 3210 Series User Manual preview
OnSite 3210 Series
Brand: Patton Pages: 110
Patton electronics 4900 Series Specification Sheet preview
4900 Series
Brand: Patton electronics Pages: 2
Patton electronics SMARTNODE 4110 Series User Manual preview
SMARTNODE 4110 Series
Brand: Patton electronics Pages: 78
Patton electronics SMARTNODE 4552 Quick Start Manual preview
SMARTNODE 4552
Brand: Patton electronics Pages: 8
Watchguard Firebox SOHO 6 Wireless Instructions Manual preview
Firebox SOHO 6 Wireless
Brand: Watchguard Pages: 8
Watchguard XTM 5 Series Hardware Manual preview
XTM 5 Series
Brand: Watchguard Pages: 24
D-Link DIR-853/EE Quick Installation Manual preview
DIR-853/EE
Brand: D-Link Pages: 83
TP-Link tl-wr845n Quick Installation Manual preview
tl-wr845n
Brand: TP-Link Pages: 2
NETGEAR DG834GT - 108 Mbps Super G Wireless ADSL Router Specifications preview
DG834GT - 108 Mbps Super G Wireless ADSL Router
Brand: NETGEAR Pages: 2
iBall Baton 150m Configuration Manual preview
150m
Brand: iBall Baton Pages: 9
RuggedCom RUGGEDMAX WIN7000 Installation Manual preview
RUGGEDMAX WIN7000
Brand: RuggedCom Pages: 42
Seriallink SLK-R602 Series Manual preview
SLK-R602 Series
Brand: Seriallink Pages: 29

Brands by name

Popular brands

Load more brands