manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

128

Configuring PROFINET

 

Information About Configuring PROFINET

PROFINET Device Roles

Figure 15

PROFINET Device Roles

An I/O controller is a programmable logic controller (PLC) that controls I/O devices and exchanges data such as 
configuration, alarms, and I/O data through an automation program. The I/O controller and the I/O supervisor exchange 
diagnostic information. The I/O controller shares configuration and input/output information with the I/O device and 
receives alarms from the I/O device. 

PROFINET is designed to be the sole or primary management system platform. Because the I/O controller detects the 
switch with the Discovery and Configuration Protocol (DCP), and sets the device name and IP address, you do not need 
to enter Cisco IOS commands for the basic configuration. For advanced configurations (for example, QoS, DHCP, and 
similar features) you must use Cisco IOS commands on the switch because these features cannot be configured by using 
PROFINET.

An I/O supervisor is an engineering station, such as a human machine interface (HMI) or PC, used for commissioning, 
monitoring, and diagnostic analysis. The I/O supervisor exchanges diagnostic, status, control, and parameter information 
with the I/O device.

An I/O device is a distributed input/output device such as a sensor, an actuator, or a motion controller. 

Note: 

If Profinet DCP cannot detect the switch/PLC/IO mac addresses, temporarily disable the firewall/virus scan from 

the Window PC that installed the Siemens STEP7 or TIA Portal.

In a PROFINET I/O system, all the I/O devices communicate over an Ethernet communication network to meet the 
automation industry requirement for bus cycle times of less than 100 ms. The network uses switches and full-duplex 
data exchange to avoid data collisions.

PROFINET Device Data Exchange

After PROFINET uses DCP to discover devices, including the switch, they establish application relationships (ARs) and 
communication relationships (CRs). After a connection is established and information about device parameters is 
exchanged, input and output data is exchanged. The switch uses non-real-time CRs to exchange the data attributes 
listed in 

Table 17 on page 129

 and 

Table 18 on page 129

.

Ethernet

3333

1

8

I/O supervisor

(Progr

a

mming device/PC)

I/O controller/PLC

I/O device

(Field device)

Commi

ss

ioning,

Pl

a

nt di

a

gno

s

tic

s

Control 

a

nd exch

a

nge

d

a

t

a

 with I/O device

s

Re

a

d 

a

nd write

I/O d

a

t

a

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

Wattle Pegasus Quick Installation Manual preview
Pegasus
Brand: Wattle Pages: 6
Baicells Nova430i Quick Manual preview
Nova430i
Brand: Baicells Pages: 8
Barco MatrixPRO-II DVI 16x16 User Manual preview
MatrixPRO-II DVI 16x16
Brand: Barco Pages: 43
Barco matrixpro-II Information Manual preview
matrixpro-II
Brand: Barco Pages: 5
Idis DR-8416 Operation Manual preview
DR-8416
Brand: Idis Pages: 123
Idis DR-6232H Installation Manual preview
DR-6232H
Brand: Idis Pages: 29
Idis DR-4516P Installation Manual preview
DR-4516P
Brand: Idis Pages: 28
Idis DirectIP DR-1304P Operation Manual preview
DirectIP DR-1304P
Brand: Idis Pages: 82
iDirect Evolution X1 Installation Manual preview
Evolution X1
Brand: iDirect Pages: 130
Quick Eagle Networks 5842 Specification Sheet preview
5842
Brand: Quick Eagle Networks Pages: 4
Enterasys X-Pedition 2000 Getting Started Manual preview
X-Pedition 2000
Brand: Enterasys Pages: 86
Allied Telesis AR725 Quick Start Manual preview
AR725
Brand: Allied Telesis Pages: 22
Lancom 7100 VPN Manual preview
7100 VPN
Brand: Lancom Pages: 70
Patton electronics SMARTNODE 4950 Quick Start Manual preview
SMARTNODE 4950
Brand: Patton electronics Pages: 12
ICP DAS USA ZT-2024 Quick Start Manual preview
ZT-2024
Brand: ICP DAS USA Pages: 8
Patton electronics Model 2711 User Manual preview
Model 2711
Brand: Patton electronics Pages: 13
Angel Cool Aironet 1200 Quick Start Manual preview
Aironet 1200
Brand: Angel Cool Pages: 2
G&D DL-DVI-Vision-IP Series Installation And Operation Manual preview
DL-DVI-Vision-IP Series
Brand: G&D Pages: 228

Brands by name

Popular brands

Load more brands