manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

675

Cisco Systems, Inc.

www.cisco.com

 

Configuring IP Multicast Routing

This chapter describes how to configure IP multicast routing on the Cisco Industrial Ethernet switch, hereafter referred 
to as 

switch

. IP multicasting is a more efficient way to use network resources, especially for bandwidth-intensive services 

such as audio and video. IP multicast routing enables a host (source) to send packets to a group of hosts (receivers) 
anywhere within the IP network by using a special form of IP address called the IP 

multicast group address.

 The sending 

host inserts the multicast group address into the IP destination address field of the packet, and IP multicast routers and 
multilayer switches forward incoming IP multicast packets out all interfaces that lead to members of the multicast group. 
Any host, regardless of whether it is a member of a group, can send to a group. However, only the members of a group 
receive the message.

Note: 

For complete syntax and usage information for the commands used in this chapter, see the documents listed in 

the 

Related Documents, page 730

.

This chapter includes the following sections:

Information About Cisco’s Implementation of IP Multicast Routing, page 675

Prerequisites, page 685

Guidelines and Limitations, page 686

Default Settings, page 688

Configuring IP Multicast Routing, page 688

Configuring Advanced PIM Features, page 710

Configuring Optional IGMP Features, page 712

Configuring Optional Multicast Routing Features, page 721

Verifying Configuration, page 725

Configuration Example, page 727

Related Documents, page 730

Information About Cisco’s Implementation of IP Multicast Routing

The switch supports these protocols to implement IP multicast routing: 

Internet Group Management Protocol (IGMP) is used among hosts on a LAN and the routers (and multilayer switches) 
on that LAN to track the multicast groups of which hosts are members.

Protocol-Independent Multicast (PIM) protocol is used among routers and multilayer switches to track which 
multicast packets to forward to each other and to their directly connected LANs. 

According to IPv4 multicast standards, the MAC destination multicast address begins with 0100:5e and is appended by 
the last 23 bits of the IP address. On the switch, if the multicast packet does not match the switch multicast address, the 
packets are treated in this way:

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

H3C H3C S7500E-X Command Reference Manual preview
H3C S7500E-X
Brand: H3C Pages: 16
H3C SR6600 SPE-FWM Configuration Manual preview
SR6600 SPE-FWM
Brand: H3C Pages: 24
National Instruments NI 9219 Operating Instructions Manual preview
NI 9219
Brand: National Instruments Pages: 36
IBM TotalStorage SAN16M-R SAN Installation And Service Manual preview
TotalStorage SAN16M-R SAN
Brand: IBM Pages: 116
Mellanox Technologies ConnectX-3 Pro MCX349A-XCCN User Manual preview
ConnectX-3 Pro MCX349A-XCCN
Brand: Mellanox Technologies Pages: 35
Hama 00176547 Operating Instruction preview
00176547
Brand: Hama Pages: 25
Infoblox Infoblox-250 Installation Manual preview
Infoblox-250
Brand: Infoblox Pages: 16
Xinje VH5 Series User Manual preview
VH5 Series
Brand: Xinje Pages: 76
Juniper WX 100 Quick Start Manual preview
WX 100
Brand: Juniper Pages: 6
VERTO 52G710 Instruction Manual preview
52G710
Brand: VERTO Pages: 48
Qlogic iSR6152 Quick Start Manual preview
iSR6152
Brand: Qlogic Pages: 12
Buffalo TERASTATION HS-D1.0TGL/R5 Technical Specifications preview
TERASTATION HS-D1.0TGL/R5
Brand: Buffalo Pages: 2
RSupport RemoteView Configuration Manual preview
RemoteView
Brand: RSupport Pages: 5
GarrettCom DynaStar DS2000-IFR Installation And Maintenance Manual preview
DynaStar DS2000-IFR
Brand: GarrettCom Pages: 40
Dahua DHI-NVR5208-4KS2 User Manual preview
DHI-NVR5208-4KS2
Brand: Dahua Pages: 361
Dahua NVR5208-EI User Manual preview
NVR5208-EI
Brand: Dahua Pages: 489
TP-Link Archer C24 Quick Installation Manual preview
Archer C24
Brand: TP-Link Pages: 2
IC Realtime Elite Series Quick Start Manual preview
Elite Series
Brand: IC Realtime Pages: 8

Brands by name

Popular brands

Load more brands