manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

66

Performing Switch Setup Configuration

 

Information About Performing Switch Setup Configuration

If the relay device is a Cisco router, enable IP routing (

ip routing

 global configuration command), and configure helper 

addresses by using the 

ip helper-address

 interface configuration command.

For example, in 

Figure 3 on page 66

, configure the router interfaces as follows:

On interface 10.0.0.2:

router(config-if)#

 ip helper-address 20.0.0.2

router(config-if)#

 ip helper-address 20.0.0.3

router(config-if)#

 ip helper-address 20.0.0.4

On interface 20.0.0.1:

router(config-if)#

 ip helper-address 10.0.0.1

Figure 3

Relay Device Used in Autoconfiguration

How to Obtain Configuration Files

Depending on the availability of the IP address and the configuration filename in the DHCP reserved lease, the switch 
obtains its configuration information in these ways:

The IP address and the configuration filename is reserved for the switch and provided in the DHCP reply (one-file 
read method).

The switch receives its IP address, subnet mask, TFTP server address, and the configuration filename from the DHCP 
server. The switch sends a unicast message to the TFTP server to retrieve the named configuration file from the base 
directory of the server and upon receipt, it completes its boot-up process.

The IP address and the configuration filename is reserved for the switch, but the TFTP server address is not provided 
in the DHCP reply (one-file read method).

The switch receives its IP address, subnet mask, and the configuration filename from the DHCP server. The switch 
sends a broadcast message to a TFTP server to retrieve the named configuration file from the base directory of the 
server, and upon receipt, it completes its boot-up process.

Only the IP address is reserved for the switch and provided in the DHCP reply. The configuration filename is not 
provided (two-file read method).

The switch receives its IP address, subnet mask, and the TFTP server address from the DHCP server. The switch 
sends a unicast message to the TFTP server to retrieve the network-confg or cisconet.cfg default configuration file. 
(If the network-confg file cannot be read, the switch reads the cisconet.cfg file.) 

Switch

(DHCP client)

Cisco router

(Relay)

49068

DHCP server

TFTP server

DNS server

20.0.0.2

20.0.0.3

20.0.0.1

10.0.0.2

10.0.0.1

20.0.0.4

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

3xLogic V250 Quick Start Manual preview
V250
Brand: 3xLogic Pages: 2
Cabletron Systems MMAC-5FNB Overview And Setup Manual preview
MMAC-5FNB
Brand: Cabletron Systems Pages: 21
Lanner NCA-2510 Installation Manual preview
NCA-2510
Brand: Lanner Pages: 2
Enginko MCF-LW06424 Operating Manual preview
MCF-LW06424
Brand: Enginko Pages: 19
Patton electronics 3087 Quick Start Manual preview
3087
Brand: Patton electronics Pages: 12
Paradyne Hotwire ATM Line Cards 8335 User Manual preview
Hotwire ATM Line Cards 8335
Brand: Paradyne Pages: 132
Ace ADSL2+ Wireless MIMO Router User Manual preview
ADSL2+ Wireless MIMO Router
Brand: Ace Pages: 64
Concept Pro DEEP LEARNING PLUS Quick Start Manual preview
DEEP LEARNING PLUS
Brand: Concept Pro Pages: 28
Atlantis Land Edge-Core A07-ES4548C Specification Sheet preview
Edge-Core A07-ES4548C
Brand: Atlantis Land Pages: 2
Parker Sporlan Division SCS-PB Series Installation And Operating Instructions Manual preview
Sporlan Division SCS-PB Series
Brand: Parker Pages: 10
TRENDnet TEG-S16R - DATA SHEETS Quick Installation Manual preview
TEG-S16R - DATA SHEETS
Brand: TRENDnet Pages: 12
YDI WL2400-ISA Installation & Operation Manual preview
WL2400-ISA
Brand: YDI Pages: 16
Extreme Networks ExtremeCloud Appliance E3120 Installation Manual preview
ExtremeCloud Appliance E3120
Brand: Extreme Networks Pages: 27
Divio NRM 311 User Manual preview
NRM 311
Brand: Divio Pages: 78
Billion BiPAC 7560G Specifications preview
BiPAC 7560G
Brand: Billion Pages: 2
Billion BiPAC 7402 Specifications preview
BiPAC 7402
Brand: Billion Pages: 2
Cambium Networks PMP 450 AP Installation Manual preview
PMP 450 AP
Brand: Cambium Networks Pages: 292
Johnson Controls IQ WiFi 6 Installation Manual preview
IQ WiFi 6
Brand: Johnson Controls Pages: 55

Brands by name

Popular brands

Load more brands