manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

731

Cisco Systems, Inc.

www.cisco.com

 

Configuring MSDP 

This chapter describes how to configure Multicast Source Discovery Protocol (MSDP) on the Cisco Industrial Ethernet 
Switches, hereafter referred to as 

switch

. MSDP connects multiple Protocol-Independent Multicast sparse-mode 

(PIM-SM) domains.

MSDP is not fully supported in this software release because of a lack of support for Multicast Border Gateway Protocol 
(MBGP), which works closely with MSDP. However, it is possible to create default peers that MSDP can operate with if 
MBGP is not running.

To use this feature, the switch must be running the IP services image. 

Note: 

For complete syntax and usage information for the commands used in this chapter, see the documents listed in 

the 

Related Documents, page 752

.

This chapter includes the following sections:

Information About MSDP, page 731

Prerequisites, page 733

Guidelines and Limitations, page 733

Default Settings, page 733

Configuring MSDP, page 733

Verifying Configuration, page 751

Configuration Example, page 751

Related Documents, page 752

Information About MSDP

MSDP allows multicast sources for a group to be known to all rendezvous points (RPs) in different domains. Each PIM-SM 
domain uses its own RPs and does not depend on RPs in other domains. An RP runs MSDP over the Transmission Control 
Protocol (TCP) to discover multicast sources in other domains. 

An RP in a PIM-SM domain has an MSDP peering relationship with MSDP-enabled devices in another domain. The 
peering relationship occurs over a TCP connection, primarily exchanging a list of sources sending to multicast groups. 
The TCP connections between RPs are achieved by the underlying routing system. The receiving RP uses the source lists 
to establish a source path.

The purpose of this topology is to have domains discover multicast sources in other domains. If the multicast sources 
are of interest to a domain that has receivers, multicast data is delivered over the normal, source-tree building 
mechanism in PIM-SM. MSDP is also used to announce sources sending to a group. These announcements must 
originate at the domain’s RP.

MSDP depends heavily on the Border Gateway Protocol (BGP) or MBGP for interdomain operation. We recommend that 
you run MSDP in RPs in your domain that are RPs for sources sending to global groups to be announced to the Internet.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

ICP DAS USA ZT-2510 Series Quick Start Manual preview
ZT-2510 Series
Brand: ICP DAS USA Pages: 8
Moxa Technologies ICS-G7748A Series Quick Installation Manual preview
ICS-G7748A Series
Brand: Moxa Technologies Pages: 10
Lancom 7100 VPN Manual preview
7100 VPN
Brand: Lancom Pages: 70
Patton electronics SMARTNODE 4950 Quick Start Manual preview
SMARTNODE 4950
Brand: Patton electronics Pages: 12
Optostar OP-8000-EDFA-1U Series Manual preview
OP-8000-EDFA-1U Series
Brand: Optostar Pages: 9
Moxa Technologies PT-7324 Series User Manual preview
PT-7324 Series
Brand: Moxa Technologies Pages: 36
Pakedge Device & Software RK-1 Quick Start Manual preview
RK-1
Brand: Pakedge Device & Software Pages: 14
Maipu SM3100-28TC-AC Install Manual preview
SM3100-28TC-AC
Brand: Maipu Pages: 19
3Com 3C433279A Release Note preview
3C433279A
Brand: 3Com Pages: 12
ZyXEL Communications SHD1110 Quick Start Manual preview
SHD1110
Brand: ZyXEL Communications Pages: 12
Planet IPOE-171-60W User Manual preview
IPOE-171-60W
Brand: Planet Pages: 20
Paradyne Hotwire 8323 Installation Instructions Manual preview
Hotwire 8323
Brand: Paradyne Pages: 6
Patton ipRocketLink 3101 Series Getting Started Manual preview
ipRocketLink 3101 Series
Brand: Patton Pages: 119
IBM Nways 2216 Service And Maintenance Manual preview
Nways 2216
Brand: IBM Pages: 168
Clas Ohlson AE222X1 Quick Start Manual preview
AE222X1
Brand: Clas Ohlson Pages: 4
XtendLan XL-VC102SB User Manual preview
XL-VC102SB
Brand: XtendLan Pages: 17
OST RuggedNet 10G/Si User Manual preview
RuggedNet 10G/Si
Brand: OST Pages: 8
Lantech TMR-5002 User Manual preview
TMR-5002
Brand: Lantech Pages: 23

Brands by name

Popular brands

Load more brands