Cisco IE 4000 Software Configuration Manual Download Page 31 | Manualshive

Page: 31 / 1066

background image

27

Configuring Interfaces

Using Interface Configuration Mode

Configuring the Console Media Type

Beginning in privileged EXEC mode, follow these steps to select the RJ-45 console media type. If you configure the
RJ-45 console, USB console operation is disabled, and input always remains with the RJ-45 console.

This example disables the USB console media type and enables the RJ-45 console media type.

Switch#

configure terminal

Switch(config)#

line console 0

Switch(config-line)#

media-type rj45

A log shows that this termination has occurred. This example shows that the console on switch reverted to RJ-45.

*Mar 1 00:25:36.860: %USB_CONSOLE-6-CONFIG_DISABLE: Console media-type USB disabled by system

configuration, media-type reverted to RJ45.

A log entry shows when a console cable is attached. If a USB console cable is connected to the switch, it is prevented
from providing input.

*Mar 1 00:34:27.498: %USB_CONSOLE-6-CONFIG_DISALLOW: Console media-type USB is disallowed by system

configuration, media-type remains RJ45.

This example reverses the previous configuration and immediately activates the USB console that is connected.

Switch#

configure terminal

Switch(config)#

line console 0

Switch(config-line)#

no media-type rj45

Using Interface Configuration Mode

The switch supports these interface types:



Physical ports—switch ports, routed ports, UNIs, NNIs, and ENIs



VLANs—switch virtual interfaces



Port-channels—EtherChannel interfaces

You can also configure a range of interfaces (see

Configuring a Range of Interfaces, page 28

).

To configure a physical interface (port), specify the interface type, the module number, and the switch port number, and
enter interface configuration mode.

Command

Purpose

1.

configure terminal

Enter global configuration mode.

2.

line console 0

Configure the console. Enter line configuration mode.

3.

media-type

rj45

Configure the console media type to always be RJ-45. If you do not
enter this command and both types are connected, the default is
USB.

4.

end

Return to privileged EXEC mode.

5.

show running-configuration

Verify your settings.

6.

copy running-config startup-config

(Optional) Save your entries in the configuration file.

«
...
29
30
31
32
33
...
»

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

Verizon DSL-2750B

Brand: D-Link Pages: 2

Brand: D-Link Pages: 4

Brand: iDirect Pages: 60

Brand: Patton electronics Pages: 75

RocketLink-G 3088/I

Brand: Patton electronics Pages: 61

Brand: Patton Pages: 12

Brand: Patton Pages: 84

OnSite 3210 Series

Brand: Patton Pages: 110

Brand: Patton electronics Pages: 2

SMARTNODE 4110 Series

Brand: Patton electronics Pages: 78

Brand: Patton electronics Pages: 8

Brand: E-TOP Pages: 76

MultiConnect SE MTS2EA

Brand: Multitech Pages: 8

DSL5068EN(1T1R)

Brand: Aztech Pages: 40

Brand: Buffalo Pages: 2

Brand: Gigabyte Pages: 18

Brand: Talent Pages: 18

Brand: Zoom Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands