manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

438

Configuring IGMP Snooping and MVR

 

How to Configure IGMP Snooping and MVR

Disabling IGMP Report Suppression

Before You Begin

IGMP report suppression is supported only when the multicast query has IGMPv1 and IGMPv2 reports. This feature is not 
supported when the query includes IGMPv3 reports.

Configuring MVR

Configuring MVR Global Parameters

You do not need to set the optional MVR parameters if you choose to use the default settings. If you do want to change 
the default parameters (except for the MVR VLAN), you must first enable MVR.

6.

ip igmp snooping querier timer expiry 

timeout

(Optional) Sets the length of time until the IGMP querier expires. The 
range is 60 to 300 seconds.

7.

ip igmp snooping querier version

 

version

(Optional) Selects the IGMP version number that the querier feature 
uses. Select 1 or 2.

8.

end

Returns to privileged EXEC mode.

Command

Purpose

Command

Purpose

1.

configure terminal

Enters global configuration mode.

2.

no ip igmp snooping report-suppression 

Disables IGMP report suppression.

3.

end

Returns to privileged EXEC mode.

Command

Purpose

1.

configure terminal

Enters global configuration mode.

2.

mvr

 

Enables MVR on the switch.

3.

mvr group 

ip-address

 [

count

]

Configures an IP multicast address on the switch or use the 

count

 parameter 

to configure a contiguous series of MVR group addresses (the range for 

count

 

is 1 to 256; the default is 1). Any multicast data sent to this address is sent to 
all source ports on the switch and all receiver ports that have elected to 
receive data on that multicast address. Each multicast address would 
correspond to one television channel.

4.

mvr querytime 

value

(Optional) Defines the maximum time to wait for IGMP report memberships 
on a receiver port before removing the port from multicast group 
membership. The value is in units of tenths of a second. The range is 1 to 100, 
and the default is 5 tenths or one-half second.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

3Com OfficeConnect 1600 Datasheet preview
OfficeConnect 1600
Brand: 3Com Pages: 8
3Com 3CRWEASY96A Quick Start Manual preview
3CRWEASY96A
Brand: 3Com Pages: 8
Paradyne Adapter Bracket Notice preview
Adapter Bracket
Brand: Paradyne Pages: 1
Hawking CF100W Specifications preview
CF100W
Brand: Hawking Pages: 2
Abocom HomePlug AV Ethernet Bridge PLE0200 Quick Install preview
HomePlug AV Ethernet Bridge PLE0200
Brand: Abocom Pages: 2
IBM 8677 - BladeCenter Rack-mountable - Power Supply Planning And Installation Manual preview
8677 - BladeCenter Rack-mountable - Power Supply
Brand: IBM Pages: 126
TP-Link Archer VR500vd Installation Manual preview
Archer VR500vd
Brand: TP-Link Pages: 7
QuickLink QL-CXS Installation Manual preview
QL-CXS
Brand: QuickLink Pages: 8
YATO YT-82380 Original Instructions Manual preview
YT-82380
Brand: YATO Pages: 96
ActionTec GT704WR User Manual preview
GT704WR
Brand: ActionTec Pages: 115
Cabletron Systems MMAC-Plus 9G536-04 User Manual preview
MMAC-Plus 9G536-04
Brand: Cabletron Systems Pages: 42
Raven RFMOW V2 User Manual preview
RFMOW V2
Brand: Raven Pages: 33
Wave Wireless Networking SPEEDLAN 4100 Installation And Operation User Manual preview
SPEEDLAN 4100
Brand: Wave Wireless Networking Pages: 167
Tripp Lite N201-007-YW Specification Sheet preview
N201-007-YW
Brand: Tripp Lite Pages: 2
QRS Q-Sync Connection Manual preview
Q-Sync
Brand: QRS Pages: 11
ADTRAN NetVanta 300 Series Quick Start Manual preview
NetVanta 300 Series
Brand: ADTRAN Pages: 2
Paradyne JetFusion 2004 User Manual preview
JetFusion 2004
Brand: Paradyne Pages: 216
Cambium Networks PMP 450i User Manual preview
PMP 450i
Brand: Cambium Networks Pages: 172

Brands by name

Popular brands

Load more brands