manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

1029

   

Configuring EtherChannels

Information About Configuring EtherChannels

Figure 109 Relationship of Physical Ports, Logical Port Channels, and Channel Groups

After you configure an EtherChannel, configuration changes applied to the port-channel interface apply to all the physical 
ports assigned to the port-channel interface. Configuration changes applied to the physical port affect only the port 
where you apply the configuration. To change the parameters of all ports in an EtherChannel, apply configuration 
commands to the port-channel interface, for example, spanning-tree commands or commands to configure a Layer 2 
EtherChannel as a trunk.

Port Aggregation Protocol

The Port Aggregation Protocol (PAgP) is a Cisco-proprietary protocol that can be run only on Cisco switches and on 
those switches licensed by vendors to support PAgP. PAgP facilitates the automatic creation of EtherChannels by 
exchanging PAgP packets between Ethernet ports.

By using PAgP, the switch learns the identity of partners capable of supporting PAgP and the capabilities of each port. It 
then dynamically groups similarly configured ports into a single logical link (channel or aggregate port). Similarly 
configured ports are grouped based on hardware, administrative, and port parameter constraints. For example, PAgP 
groups the ports with the same speed, duplex mode, native VLAN, VLAN range, and trunking status and type. After 
grouping the links into an EtherChannel, PAgP adds the group to the spanning tree as a single switch port.

PAgP Modes 

Table 69User-Configurable EtherChannel PAgP Modes, page 1030

 shows the user-configurable EtherChannel PAgP 

modes for the 

channel-group

 interface configuration command. 

101238

Channel-group
binding

Physical ports

Logical

port-channel

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

D-Link DSL-2750U Quick Start Manual preview
DSL-2750U
Brand: D-Link Pages: 2
Observint N16 Quick Setup Manual preview
N16
Brand: Observint Pages: 11
F5 i5000 Series Platform Manual preview
i5000 Series
Brand: F5 Pages: 72
Funkwerk TR 200 aw/ bw Operating Instructions preview
TR 200 aw/ bw
Brand: Funkwerk Pages: 2
Supermicro SC836 X9 User Manual preview
SC836 X9
Brand: Supermicro Pages: 24
Aztech DSL1000EW(L) Speci?Cations preview
DSL1000EW(L)
Brand: Aztech Pages: 2
Aruba IntroSpect Analyzer 2 Series Quick Start Manual preview
IntroSpect Analyzer 2 Series
Brand: Aruba Pages: 5
Extron electronics PoleVault System A/V Source Inputs Specification Sheet preview
PoleVault System A/V Source Inputs
Brand: Extron electronics Pages: 4
HMS Networks Anybus Communicator ABC4021 User Manual preview
Anybus Communicator ABC4021
Brand: HMS Networks Pages: 60
Magnadyne RV2458 Installation Manual preview
RV2458
Brand: Magnadyne Pages: 8
Gbord EN-101 User Manual preview
EN-101
Brand: Gbord Pages: 8
insys icom EBW-E Quick Installation Manual preview
EBW-E
Brand: insys icom Pages: 4
ZyXEL Communications XS1920 Series User Manual preview
XS1920 Series
Brand: ZyXEL Communications Pages: 422
National Instruments PXI PXITM -1000 User Manual preview
PXI PXITM -1000
Brand: National Instruments Pages: 55
LevelOne NetCon FBR-1409TX User Manual preview
NetCon FBR-1409TX
Brand: LevelOne Pages: 88
Handicare DX REM 420 User Manual preview
DX REM 420
Brand: Handicare Pages: 60
Zalip CDE570AM-U User Manual preview
CDE570AM-U
Brand: Zalip Pages: 76
Riverbed SteelCentral NetExpress 470 Upgrade And Maintenance Manual preview
SteelCentral NetExpress 470
Brand: Riverbed Pages: 140

Brands by name

Popular brands

Load more brands