manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

754

Configuring IPv6 MLD Snooping

 

Information About MLD Snooping

Note: 

The switch does not support MLDv2 enhanced snooping (MESS), which sets up IPv6 source and destination 

multicast address-based forwarding.

MLD snooping can be enabled or disabled globally or per VLAN. When MLD snooping is enabled, a per-VLAN IPv6 
multicast MAC address table is constructed in software and a per-VLAN IPv6 multicast address table is constructed in 
software and hardware. The switch then performs IPv6 multicast-address based bridging in hardware. 

These sections describe some parameters of IPv6 MLD snooping:

MLD Messages, page 754

MLD Queries, page 754

Multicast Client Aging Robustness, page 755

Multicast Router Discovery, page 755

MLD Reports, page 755

MLD Done Messages and Immediate-Leave, page 756

Topology Change Notification Processing, page 756

MLD Messages

MLDv1 supports three types of messages:

Listener Queries are the equivalent of IGMPv2 queries and are either General Queries or Multicast-Address-Specific 
Queries (MASQs).

Multicast Listener Reports are the equivalent of IGMPv2 reports.

Multicast Listener Done messages are the equivalent of IGMPv2 leave messages. 

MLDv2 supports MLDv2 queries and reports, as well as MLDv1 Report and Done messages. 

Message timers and state transitions resulting from messages being sent or received are the same as those of IGMPv2 
messages. MLD messages that do not have valid link-local IPv6 source addresses are ignored by MLD routers and 
switches. 

MLD Queries

The switch sends out MLD queries, constructs an IPv6 multicast address database, and generates MLD group-specific 
and MLD group-and-source-specific queries in response to MLD Done messages. The switch also supports report 
suppression, report proxying, Immediate-Leave functionality, and static IPv6 multicast MAC-address configuration.

When MLD snooping is disabled, all MLD queries are flooded in the ingress VLAN.

When MLD snooping is enabled, received MLD queries are flooded in the ingress VLAN, and a copy of the query is sent 
to the CPU for processing. From the received query, MLD snooping builds the IPv6 multicast address database. It detects 
multicast router ports, maintains timers, sets report response time, learns the querier IP source address for the VLAN, 
learns the querier port in the VLAN, and maintains multicast-address aging. 

Note: 

When the IPv6 multicast router is a Catalyst 6500 switch and you are using extended VLANs (in the range 1006 to 

4094), IPv6 MLD snooping must be enabled on the extended VLAN on the Catalyst 6500 switch in order for this switch 
to receive queries on the VLAN. For normal-range VLANs (1 to 1005), it is not necessary to enable IPv6 MLD snooping 
on the VLAN on the Catalyst 6500 switch.

When a group exists in the MLD snooping database, the switch responds to a group-specific query by sending an MLDv1 
report. When the group is unknown, the group-specific query is flooded to the ingress VLAN. 

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

PaloAlto Networks PA-5400 Series Quick Start Manual preview
PA-5400 Series
Brand: PaloAlto Networks Pages: 2
MikroTik RouterBOARD SXT 5HnD Quick Setup Manual And Warranty Information preview
RouterBOARD SXT 5HnD
Brand: MikroTik Pages: 2
Texas Instruments ThunderLAN TNETE100A Programmer'S Manual preview
ThunderLAN TNETE100A
Brand: Texas Instruments Pages: 179
Delta Electronics Ethernet Communication Module DVPEN01-SL Manual preview
Ethernet Communication Module DVPEN01-SL
Brand: Delta Electronics Pages: 54
FS FS-BOX-V3 Quick Start Manual preview
FS-BOX-V3
Brand: FS Pages: 19
NEC P401-TMX4D User Manual preview
P401-TMX4D
Brand: NEC Pages: 2
Compaq StorageWorks AIT 35GB AutoLoader Overview And Installation preview
StorageWorks AIT 35GB AutoLoader
Brand: Compaq Pages: 4
Z Microsystems TranzStor 8X User Manual preview
TranzStor 8X
Brand: Z Microsystems Pages: 51
Balluff Easy Tool-ID BSG TID-05-T30-00-005 Installation And Operation Manual preview
Easy Tool-ID BSG TID-05-T30-00-005
Brand: Balluff Pages: 46
MEMON memonizerWORKSTATION Quick Start Manual preview
memonizerWORKSTATION
Brand: MEMON Pages: 2
ADC HiGain H2TU-R-402 List 7A Quick Installation preview
HiGain H2TU-R-402 List 7A
Brand: ADC Pages: 7
Renesas H8S/2633 User Manual preview
H8S/2633
Brand: Renesas Pages: 28
Mellanox Technologies ConnectX-3 Pro MCX349A-XCCN User Manual preview
ConnectX-3 Pro MCX349A-XCCN
Brand: Mellanox Technologies Pages: 35
Caen A 1735 Technical Information Manual preview
A 1735
Brand: Caen Pages: 14
Patton IPLink 2603 Series User Manual preview
IPLink 2603 Series
Brand: Patton Pages: 120
National Instruments PXI Terminal Block NI TB-2709 Installation Manual preview
PXI Terminal Block NI TB-2709
Brand: National Instruments Pages: 12
Telestar DIGIBIT R1 Operating Manual preview
DIGIBIT R1
Brand: Telestar Pages: 16
Planet FGSW-2620 User Manual preview
FGSW-2620
Brand: Planet Pages: 13

Brands by name

Popular brands

Load more brands