manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

973

Cisco Systems, Inc.

www.cisco.com

 

Dying Gasp

This chapter describes the Dying-Gasp feature for the Cisco Industrial Ethernet series switches.

Dying Gasp resides on a hardware component on the High-performance WAN Interface Card (HWIC) and supports 
Gigabit Ethernet interfaces. The networking devices rely on a temporary back-up power supply on a capacitor, that allows 
for a graceful shutdown and the generation of the dying-gasp message. This temporary power supply is designed to last 
from 10 to 20 milliseconds to perform these tasks. 

Dying-Gasp packets are created when you configure the host by using the 

dying-gasp

 configuration command. The 

show dying-gasp packets

 command displays the detailed information about the created packets. 

The SNMP server for the SNMP Dying Gasp message is specified through the 

snmp-server host

 configuration 

command. The syslog server sending the syslog Dying Gasp message is specified through the 

logging host 

hostname-or-ipaddress transport udp

 command. The Ethernet-OAM Dying Gasp packets are created for interfaces 

where Ethernet-OAM is enabled.

Dying Gasp packets can be sent to a maximum number of 5 servers for each notification type.

For more information about configuring Dying Gasp, see the Configuring Dying Gasp chapter of the System Management 
guide at this URL: 

http://www.cisco.com/c/en/us/td/docs/switches/connectedgrid/cg-switch-sw-master/software/configuration/guide/
sysmgmt/CGS_1000_Sysmgmt/cgs_dying_gasp.html

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

E-Lins H900 Series User Manual preview
H900 Series
Brand: E-Lins Pages: 59
E-Lins H750 Quick Start Manual preview
H750
Brand: E-Lins Pages: 11
E-Lins H700 Series Quick Start Manual preview
H700 Series
Brand: E-Lins Pages: 9
E-Lins H685 Series Quick Start preview
H685 Series
Brand: E-Lins Pages: 5
e-Line Technology Network Video Recorders User Manual preview
Network Video Recorders
Brand: e-Line Technology Pages: 34
JB Systems Scene Master Operation Manual preview
Scene Master
Brand: JB Systems Pages: 24
JB Systems CMX 24 User Manual preview
CMX 24
Brand: JB Systems Pages: 61
Patton electronics Patton SmartNode 2300 Series Specification Sheet preview
Patton SmartNode 2300 Series
Brand: Patton electronics Pages: 2
Paradyne 8540 Installation Instructions Manual preview
8540
Brand: Paradyne Pages: 12
ADTRAN NetVanta 6355 PoE Installation Manual preview
NetVanta 6355 PoE
Brand: ADTRAN Pages: 46
Patton electronics 6103 User Manual preview
6103
Brand: Patton electronics Pages: 12
American Megatrends StorTrends 1312-P Specifications preview
StorTrends 1312-P
Brand: American Megatrends Pages: 2
ZyXEL Communications P-974H - V3.70 Manual preview
P-974H - V3.70
Brand: ZyXEL Communications Pages: 116
Watchguard XTM 850 Hardware Manual preview
XTM 850
Brand: Watchguard Pages: 30
JUMO 705041 Installation Instructions Manual preview
705041
Brand: JUMO Pages: 60
National Instruments Monochrome Image Acquisition Device NI 1410 User Manual preview
Monochrome Image Acquisition Device NI 1410
Brand: National Instruments Pages: 34
Broadband Products Xtreme Networked Boat User Manual preview
Xtreme Networked Boat
Brand: Broadband Products Pages: 16
Comtrend Corporation AR-5319 User Manual preview
AR-5319
Brand: Comtrend Corporation Pages: 208

Brands by name

Popular brands

Load more brands