manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

286

Configuring VLANs

 

How to Configure VLANs

Creating an Extended-Range VLAN with an Internal VLAN ID

Configuring an Ethernet Interface as a Trunk Port

Command

Purpose

1.

show vlan internal usage

Displays the VLAN IDs being used internally by the switch. If the VLAN ID 
that you want to use is an internal VLAN, the display shows the routed 
port that is using the VLAN ID. Enter that port number in Step 3.

2.

configure terminal

Enters global configuration mode.

3.

interface 

interface-id

Specifies the interface ID for the routed port that is using the VLAN ID, 
and enters interface configuration mode.

4.

shutdown

Shuts down the port to free the internal VLAN ID.

5.

exit

Returns to global configuration mode.

6.

vtp mode transparent

Sets the VTP mode to transparent for creating extended-range VLANs.

Note: 

This step is not required for VTP version 3.

7.

vlan

 

vlan-id

Enters the new extended-range VLAN ID, and enters VLAN configuration 
mode.

8.

exit

Exits from VLAN configuration mode, and returns to global configuration 
mode.

9.

interface 

interface-id

Specifies the interface ID for the routed port that you shut down in Step 
4, and enters interface configuration mode. 

10.

no shutdown

Reenables the routed port. It will be assigned a new internal VLAN ID.

11.

end

Returns to privileged EXEC mode.

Command

Purpose

1.

configure terminal

Enters global configuration mode.

2.

interface 

interface-id

Specifies the port to be configured for trunking, and enters interface 
configuration mode.

3.

switchport mode 

{

dynamic

 {

auto

 | 

desirable

} | 

trunk

}

Configures the interface as a Layer 2 trunk (required only if the interface 
is a Layer 2 access port or tunnel port or to specify the trunking mode).

dynamic auto

—Sets the interface to a trunk link if the neighboring 

interface is set to trunk or desirable mode. This is the default.

dynamic desirable

—Sets the interface to a trunk link if the 

neighboring interface is set to trunk, desirable, or auto mode.

trunk

—Sets the interface in permanent trunking mode and negotiate 

to convert the link to a trunk link even if the neighboring interface is 
not a trunk interface.

4.

switchport access vlan

 

vlan-id

(Optional) Specifies the default VLAN, which is used if the interface stops 
trunking.

5.

switchport trunk native vlan

 

vlan-id

Specifies the native VLAN for IEEE 802.1Q trunks. 

6.

end

Returns to privileged EXEC mode.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

Tripp Lite N125-010-GY Specification Sheet preview
N125-010-GY
Brand: Tripp Lite Pages: 2
insys icom EBW-E Quick Installation Manual preview
EBW-E
Brand: insys icom Pages: 4
IDT 89HPES16NT2 User Manual preview
89HPES16NT2
Brand: IDT Pages: 292
PairGain T1L2N20A Manual preview
T1L2N20A
Brand: PairGain Pages: 80
RTS AIO-8 Drawings Manual preview
AIO-8
Brand: RTS Pages: 3
ADTRAN TRACER 5045 Manual preview
TRACER 5045
Brand: ADTRAN Pages: 9
Alcatel-Lucent 1353 Brochure preview
1353
Brand: Alcatel-Lucent Pages: 12
Avigilon NVR5-STD-10GBE Installation Manual preview
NVR5-STD-10GBE
Brand: Avigilon Pages: 12
ActionTec MI424WR MI424WR Upgrade Procedure preview
MI424WR
Brand: ActionTec MI424WR Pages: 3
Erbauer 3663602796282 Original Instructions Manual preview
3663602796282
Brand: Erbauer Pages: 36
Eaton 9479-ETG-CSL Instruction Manual preview
9479-ETG-CSL
Brand: Eaton Pages: 32
Lantech TMR-5002 User Manual preview
TMR-5002
Brand: Lantech Pages: 23
netsys NH-310S User Manual preview
NH-310S
Brand: netsys Pages: 38
G&D DP1.2-Vision-IP-Fiber Installation And Operation Manual preview
DP1.2-Vision-IP-Fiber
Brand: G&D Pages: 240
Kasda KA1750 User Manual preview
KA1750
Brand: Kasda Pages: 44
Bdcom GP3600-16 Hardware Installation Manual preview
GP3600-16
Brand: Bdcom Pages: 25
Baicells Aurora243 Installation Manual preview
Aurora243
Brand: Baicells Pages: 38
Zmotion ECI3808 Manual preview
ECI3808
Brand: Zmotion Pages: 57

Brands by name

Popular brands

Load more brands