manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

271

Cisco Systems, Inc.

www.cisco.com

 

Configuring VLANs 

Information About Configuring 

VLANs

 

VLANs

A VLAN is a switched network that is logically segmented by function, project team, or application, without regard to the 
physical locations of the users. VLANs have the same attributes as physical LANs, but you can group end stations even 
if they are not physically located on the same LAN segment. Any switch port can belong to a VLAN, and unicast, 
broadcast, and multicast packets are forwarded and flooded only to end stations in the VLAN. Each VLAN is considered 
a logical network, and packets destined for stations that do not belong to the VLAN must be forwarded through a router 
or a switch supporting fallback bridging, as shown in 

Figure 29 on page 271

. Because a VLAN is considered a separate 

logical network, it contains its own bridge Management Information Base (MIB) information and can support its own 
implementation of spanning tree. See 

Configuring STP, page 315

Note: 

Before you create VLANs, you must decide whether to use VLAN Trunking Protocol (VTP) to maintain global VLAN 

configuration for your network. 

Figure 29

VLANs as Logically Defined Networks

VLANs are often associated with IP subnetworks. For example, all the end stations in a particular IP subnet belong to the 
same VLAN. Interface VLAN membership on the switch is assigned manually on an interface-by-interface basis. When 
you assign switch interfaces to VLANs by using this method, it is known as interface-based, or static, VLAN membership.

Floor 1

Floor 2

Engineering

VLAN

Cisco router

Gigabit

Ethernet

Floor 3

Marketing

VLAN

Accounting

VLAN

90571

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

TC Electronic DB6 User Manual preview
DB6
Brand: TC Electronic Pages: 174
Juniper TX MATRIX PLUS Hardware Manual preview
TX MATRIX PLUS
Brand: Juniper Pages: 502
TP-Link TL-MR3220 Quick Installation Manual preview
TL-MR3220
Brand: TP-Link Pages: 87
Ubiquiti EdgeRouter PoE ERPoe-5 Quick Start Manual preview
EdgeRouter PoE ERPoe-5
Brand: Ubiquiti Pages: 13
AOpen ISDN SOHO Router User Manual preview
ISDN SOHO Router
Brand: AOpen Pages: 89
Federal Signal Corporation AR2000-M Installation And Maintenance Manual preview
AR2000-M
Brand: Federal Signal Corporation Pages: 49
Dahua NVR41-4KS2 Series User Manual preview
NVR41-4KS2 Series
Brand: Dahua Pages: 452
Alcatel-Lucent 9364 Installation And Commissioning Manual preview
9364
Brand: Alcatel-Lucent Pages: 60
Behringer B-Control Fader BCF2000 Quick Start Manual preview
B-Control Fader BCF2000
Brand: Behringer Pages: 13
RR-Concepts StationMaster Manual preview
StationMaster
Brand: RR-Concepts Pages: 12
ExtraHop EDA 4200 Install preview
EDA 4200
Brand: ExtraHop Pages: 2
TRENDnet TDM-C400 User Manual preview
TDM-C400
Brand: TRENDnet Pages: 205
RouterBOARD OmniTik UPA-5HnD Quick Setup Manual And Warranty Information preview
OmniTik UPA-5HnD
Brand: RouterBOARD Pages: 4
LevelOne FUS-3100 Quick Installation Manual preview
FUS-3100
Brand: LevelOne Pages: 61
Tripp Lite N304-15M Specification Sheet preview
N304-15M
Brand: Tripp Lite Pages: 2
Tripp Lite N304-11M Specification Sheet preview
N304-11M
Brand: Tripp Lite Pages: 2
IDT 89HPES12T3G2 Preliminary User'S Manual preview
89HPES12T3G2
Brand: IDT Pages: 146
Keysight Technologies Ixia APS-M1010 Installation Manual preview
Ixia APS-M1010
Brand: Keysight Technologies Pages: 31

Brands by name

Popular brands

Load more brands