manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

658

Configuring IPv6 Host Functions

 

Information About Configuring IPv6 Host Functions

You can also use two colons (::) to represent successive hexadecimal fields of zeros, but you can use this short version 
only once in each address:

2031:0:130F::09C0:080F:130B

For more information about IPv6 address formats, address types, and the IPv6 packet header, see the “Implementing 
IPv6 Addressing and Basic Connectivity” chapter of 

Cisco IOS IPv6 Configuration Library 

on Cisco.com.

In the “Implementing Addressing and Basic Connectivity” chapter, these sections apply to the switch:

IPv6 Address Formats

IPv6 Address Output Display

Simplified IPv6 Packet Header

Supported IPv6 Host Features

These sections describe the IPv6 protocol features supported by the switch:

128-Bit Wide Unicast Addresses, page 658

DNS for IPv6, page 659

ICMPv6, page 659

Neighbor Discovery, page 659

Default Router Preference, page 659

IPv6 Stateless Autoconfiguration and Duplicate Address Detection, page 659

IPv6 Applications, page 660

Dual IPv4 and IPv6 Protocol Stacks, page 660

SNMP and Syslog Over IPv6, page 661

HTTP over IPv6, page 661

Support on the switch includes expanded address capability, header format simplification, improved support of 
extensions and options, and hardware parsing of the extension header. The switch supports hop-by-hop extension 
header packets, which are routed or bridged in software.

128-Bit Wide Unicast Addresses 

The switch supports aggregatable global unicast addresses and link-local unicast addresses. It does not support 
site-local unicast addresses.

Aggregatable global unicast addresses are IPv6 addresses from the aggregatable global unicast prefix. The address 
structure enables strict aggregation of routing prefixes and limits the number of routing table entries in the global 
routing table. These addresses are used on links that are aggregated through organizations and eventually to the 
Internet service provider.

These addresses are defined by a global routing prefix, a subnet ID, and an interface ID. Current global unicast 
address allocation uses the range of addresses that start with binary value 001 (2000::/3). Addresses with a prefix 
of 2000::/3(001) through E000::/3(111) must have 64-bit interface identifiers in the extended unique identifier 
(EUI)-64 format. 

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

NEC Express5800/E120d-M Getting Started preview
Express5800/E120d-M
Brand: NEC Pages: 2
3Com OfficeConnect 1600 Datasheet preview
OfficeConnect 1600
Brand: 3Com Pages: 8
3Com 3CRWEASY96A Quick Start Manual preview
3CRWEASY96A
Brand: 3Com Pages: 8
impinj Speedway Revolution Installation And Operation Manual preview
Speedway Revolution
Brand: impinj Pages: 60
Xenya XS26GS User Manual preview
XS26GS
Brand: Xenya Pages: 189
B+B SmartWorx spectre lte User Manual preview
spectre lte
Brand: B+B SmartWorx Pages: 52
Kohler Mira Pixel User Manual preview
Mira Pixel
Brand: Kohler Pages: 32
WABCO CAN Router Manual preview
CAN Router
Brand: WABCO Pages: 29
Patton electronics FORESIGHT 6300 User Manual preview
FORESIGHT 6300
Brand: Patton electronics Pages: 145
TP-Link TD-8840 User Manual preview
TD-8840
Brand: TP-Link Pages: 25
Tripp Lite N304-025 Specification Sheet preview
N304-025
Brand: Tripp Lite Pages: 2
ROBOfiber RB-GES401-POE User Manual preview
RB-GES401-POE
Brand: ROBOfiber Pages: 2
Epson C82314* User Manual preview
C82314*
Brand: Epson Pages: 71
Epson C8230 Series User Manual preview
C8230 Series
Brand: Epson Pages: 29
Epson C82324* User Manual preview
C82324*
Brand: Epson Pages: 57
Epson C823312 (Ethernet) User Manual preview
C823312 (Ethernet)
Brand: Epson Pages: 76
Crestron 2 Channel Inductor Module CLX-2IND Specification Sheet preview
2 Channel Inductor Module CLX-2IND
Brand: Crestron Pages: 1
Linksys HPES03 User Manual preview
HPES03
Brand: Linksys Pages: 17

Brands by name

Popular brands

Load more brands