manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

119

   

Performing Switch Administration

How to Perform Switch Administration

Adding and Removing Static Address Entries

Configuring Unicast MAC Address Filtering

Disabling MAC Address Learning on a VLAN

Command

Purpose

1.

configure terminal

Enters global configuration mode.

2.

mac address-table static 

mac-addr 

vlan

 vlan-id 

interface

 interface-id 

Adds a static address to the MAC address table.

mac-addr

—Specifies the destination MAC unicast address to add to 

the address table. Packets with this destination address received in 
the specified VLAN are forwarded to the specified interface.

vlan-id

—Specifies the VLAN for which the packet with the specified 

MAC address is received. Valid VLAN IDs are 1 to 4096.

interface-id

—Specifies the interface to which the received packet is 

forwarded. Valid interfaces include physical ports or port channels. 
For static multicast addresses, you can enter multiple interface IDs. 
For static unicast addresses, you can enter only one interface at a 
time, but you can enter the command multiple times with the same 
MAC address and VLAN ID. 

3.

end

Returns to privileged EXEC mode.

Command

Purpose

1.

configure terminal

Enters global configuration mode.

2.

mac address-table static 

mac-addr 

vlan

 vlan-id 

drop

 

Enables unicast MAC address filtering and configures the switch to drop 
a packet with the specified source or destination unicast static address.

mac-addr

—Specifies a source or destination unicast MAC address. 

Packets with this MAC address are dropped.

vlan-id

—Specifies the VLAN for which the packet with the specified 

MAC address is received. Valid VLAN IDs are 1 to 4096.

3.

end

Returns to privileged EXEC mode.

Command

Purpose

1.

configure terminal

Enters global configuration mode.

2.

no mac address-table learning vlan

 

vlan-id 

Disables MAC address learning on the specified VLAN or VLANs. You can 
specify a single VLAN ID or a range of VLAN IDs separated by a hyphen 
or comma. Valid VLAN IDs are 1 to 4096.

3.

end

Returns to privileged EXEC mode.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

National Instruments SCXI-1121 User Manual preview
SCXI-1121
Brand: National Instruments Pages: 162
IBM 8677 - BladeCenter Rack-mountable - Power Supply Planning And Installation Manual preview
8677 - BladeCenter Rack-mountable - Power Supply
Brand: IBM Pages: 126
Patton electronics SmartNode 4520 Series Getting Started Manual preview
SmartNode 4520 Series
Brand: Patton electronics Pages: 90
Idis DR-1508P Operation Manual preview
DR-1508P
Brand: Idis Pages: 85
INNOSILICON T3-43T User Manual preview
T3-43T
Brand: INNOSILICON Pages: 11
NBase NH 210 Installation And User Manual preview
NH 210
Brand: NBase Pages: 18
Gearlinx NR4400 Series User'S Quick Start Manual preview
NR4400 Series
Brand: Gearlinx Pages: 23
ZyXEL Communications GS1100-10HP User Manual preview
GS1100-10HP
Brand: ZyXEL Communications Pages: 30
LevelOne WBR-3402TX User Manual preview
WBR-3402TX
Brand: LevelOne Pages: 146
Extron electronics VERSATOOLS MTP User Manual preview
VERSATOOLS MTP
Brand: Extron electronics Pages: 19
FOR-A USF-105PS Operation Manuals preview
USF-105PS
Brand: FOR-A Pages: 37
Ubiquiti EdgePoint EP-R8 Quick Start Manual preview
EdgePoint EP-R8
Brand: Ubiquiti Pages: 22
Xtatix XCA-PDSI User Manual preview
XCA-PDSI
Brand: Xtatix Pages: 12
Positron TeleLite 720920 Series Manual preview
TeleLite 720920 Series
Brand: Positron Pages: 21
ProCurve J8451A Quick Start Manual preview
J8451A
Brand: ProCurve Pages: 2
ProCurve 800 Configuration Manual preview
800
Brand: ProCurve Pages: 406
Crestron HDMI Input Card DMC-HD Specifications preview
HDMI Input Card DMC-HD
Brand: Crestron Pages: 1
Crestron Zum Installation Manual preview
Zum
Brand: Crestron Pages: 2

Brands by name

Popular brands

Load more brands