manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

440

Configuring IGMP Snooping and MVR

 

How to Configure IGMP Snooping and MVR

Configuring IGMP

Configuring IGMP Profiles

Configuring IGMP Interfaces

Command

Purpose

1.

configure terminal

Enters global configuration mode.

2.

ip igmp profile 

profile number

Assigns a number to the profile you are configuring, and enter IGMP 
profile configuration mode. The profile number range is 1 to 
4294967295.

3.

permit | deny

(Optional) Sets the action to permit or deny access to the IP multicast 
address. If no action is configured, the default for the profile is to deny 
access.

4.

range

 ip multicast address

Enters the IP multicast address or range of IP multicast addresses to 
which access is being controlled. If entering a range, enter the low IP 
multicast address, a space, and the high IP multicast address.

You can use the 

range

 command multiple times to enter multiple 

addresses or ranges of addresses.

5.

end 

Returns to privileged EXEC mode.

Command

Purpose

1.

configure terminal

Enters global configuration mode.

2.

interface 

interface-id

Specifies the physical interface, and enter interface configuration mode. 
The interface must be a Layer 2 port that does not belong to an 
EtherChannel port group.

3.

ip igmp filter 

profile number

Applies the specified IGMP profile to the interface. The range is 1 to 
4294967295.

4.

ip igmp max-groups 

number

Sets the maximum number of IGMP groups that the interface can join. 
The range is 0 to 4294967294. The default is to have no maximum set.

5.

ip igmp max-groups action 

{

deny | 

replace

}

When an interface receives an IGMP report and the maximum number 
of entries is in the forwarding table, specify the action that the interface 
takes:

deny

—Drops the report.

replace

—Replaces the existing group with the new group for which 

the IGMP report was received.

6.

end 

Returns to privileged EXEC mode.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

2N OfficeRoute Quick Manual preview
OfficeRoute
Brand: 2N Pages: 11
2N stargate How To Set preview
stargate
Brand: 2N Pages: 5
2N Telekomunikace EasyGate IP Brief Manual preview
EasyGate IP
Brand: 2N Telekomunikace Pages: 24
Qixiang Technology QR310 Installation And Configuration Quick Manual preview
QR310
Brand: Qixiang Technology Pages: 16
Dazzle Hollywood DV-Bridge User Manual preview
Hollywood DV-Bridge
Brand: Dazzle Pages: 63
Garland EdgeLens INT10G8LR56 User Manual preview
EdgeLens INT10G8LR56
Brand: Garland Pages: 30
NETGEAR RH328 Reference Manual preview
RH328
Brand: NETGEAR Pages: 142
Aaeon FWS-7150 Manual preview
FWS-7150
Brand: Aaeon Pages: 57
Juniper NSM4000 Hardware Manual preview
NSM4000
Brand: Juniper Pages: 196
SainSmart Genmitsu CNC Assembly Instruction Manual preview
Genmitsu CNC
Brand: SainSmart Pages: 12
Vivint AirBridge VS-YOFIMN-000 Quick Reference preview
AirBridge VS-YOFIMN-000
Brand: Vivint Pages: 2
FiberHome AN5506-04-B User Manual preview
AN5506-04-B
Brand: FiberHome Pages: 44
MCT MPU100ZW User Manual preview
MPU100ZW
Brand: MCT Pages: 12
Calix GigaSpire BLAST u4hm Installation Manual preview
GigaSpire BLAST u4hm
Brand: Calix Pages: 45
Rajant BreadCrumb ES1 User Manual preview
BreadCrumb ES1
Brand: Rajant Pages: 93
Westermo LRW-112 Series Manual preview
LRW-112 Series
Brand: Westermo Pages: 28
Ubiquiti EdgeRouter X ER-X-SFP Quick Start Manual preview
EdgeRouter X ER-X-SFP
Brand: Ubiquiti Pages: 20
SMC Networks Barricade SMC7908VoWBRA2 Specifications preview
Barricade SMC7908VoWBRA2
Brand: SMC Networks Pages: 2

Brands by name

Popular brands

Load more brands