manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

590

Configuring QoS

 

QoS Treatment for Performance-Monitoring Protocols

Figure 81

Marking of Classified Traffic 

This example uses a policy map to remark a packet. The first marking (the 

set

 command) applies to the QoS default class 

map that matches all traffic not matched by class 

AF31-AF33

 and sets all traffic to an IP DSCP value of 1. The second 

marking sets the traffic in classes AF31 to AF33 to an IP DSCP of 3.

Switch(config)# 

policy-map Example

Switch(config-pmap)# 

class class-default

Switch(config-pmap-c)# 

set ip dscp 1

Switch(config-pmap-c)# 

exit

Switch(config-pmap)# 

class AF31-AF33

Switch(config-pmap-c)# 

set ip dscp 3

Switch(config-pmap-c)# 

exit

Switch(config-pmap)# 

exit

Switch(config)# 

interface fastethernet0/1

Switch(config-if)# 

service-policy input Example

 

Switch(config-if)# 

exit

QoS Treatment for Performance-Monitoring Protocols

Two-Way Active Measurement Protocol, page 590

QoS Treatment for IP-SLA and TWAMP Probes, page 590

QoS Marking for CPU-Generated Traffic, page 591

QoS Queuing for CPU-Generated Traffic, page 592

Configuration Guidelines, page 592

Two-Way Active Measurement Protocol

For information about the Two-Way Active Measurement Protocol (TWAMP), see 

Understanding TWAMP, page 41-14

 

and 

Configuring TWAMP, page 41-15

.

QoS Treatment for IP-SLA and TWAMP Probes

The QoS treatment for IP-SLA and TWAMP probes must exactly reflect the effects that occur to the normal data traffic 
crossing the device. 

The generating device should not change the probe markings. It should queue these probes based on the configured 
queueing policies for normal traffic. 

Marking 

By default, the class of service (CoS) marking of CFM traffic (including IP SLAs using CFM probes) is not changed. This 
feature cannot change this behavior.

By default, IP traffic marking (including IP SLA and TWAMP probes) is not changed. This feature can change this behavior.

157193

Receive

Classify

Queuing,
scheduling,
and shaping

Unconditionally
mark traffic for
reclassification

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

3xLogic V250 Quick Start Manual preview
V250
Brand: 3xLogic Pages: 2
LaCie 8BIG RACK THUNDERBOLT 2 Quick Start Manual preview
8BIG RACK THUNDERBOLT 2
Brand: LaCie Pages: 28
QTech QSR-3920 Series Configuration Manual preview
QSR-3920 Series
Brand: QTech Pages: 120
Safety Vision ROADRECORDER 8000 User Manual preview
ROADRECORDER 8000
Brand: Safety Vision Pages: 40
Grasslin TOWERCHRON DP72 Programming Manual preview
TOWERCHRON DP72
Brand: Grasslin Pages: 2
Dahua DHI-NVR2104-P-4KS2 Quick Start Manual preview
DHI-NVR2104-P-4KS2
Brand: Dahua Pages: 23
HELVAR Imagine 920 Installation Manual preview
Imagine 920
Brand: HELVAR Pages: 2
TP-Link TL-MR3220 Quick Installation Manual preview
TL-MR3220
Brand: TP-Link Pages: 87
National Instruments FieldPoint FP-3000 User Manual preview
FieldPoint FP-3000
Brand: National Instruments Pages: 118
Intel IXP45X Developer'S Manual preview
IXP45X
Brand: Intel Pages: 958
Supero SUPERSERVER 6027TR-H71FRF User Manual preview
SUPERSERVER 6027TR-H71FRF
Brand: Supero Pages: 118
SmartBridges airHaul Nexus sB3010 User Manual preview
airHaul Nexus sB3010
Brand: SmartBridges Pages: 80
Ethernet Direct Husky HMG-1648EP User Manual preview
Husky HMG-1648EP
Brand: Ethernet Direct Pages: 16
V-Count Ultima Go Quick Installation Manual preview
Ultima Go
Brand: V-Count Pages: 2
Lanner NCA-6520 User Manual preview
NCA-6520
Brand: Lanner Pages: 141
ADTRAN DUAL Nx56/64 1200142L1# User Manual preview
DUAL Nx56/64 1200142L1#
Brand: ADTRAN Pages: 48
Black Box LGB2003A User Manual preview
LGB2003A
Brand: Black Box Pages: 62
ATEN Altusen SN0100 Series User Manual preview
Altusen SN0100 Series
Brand: ATEN Pages: 178

Brands by name

Popular brands

Load more brands