manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

1038

Configuring EtherChannels

 

How to Configure EtherChannels

Configuring EtherChannel Load Balancing

This task is optional.

3.

switchport mode

 {

access

 | 

trunk

}

switchport access vlan 

vlan-id

 

Assigns all ports as static-access ports in the same VLAN, or 
configures them as trunks.

If you configure the port as a static-access port, assign it to only 
one VLAN. The range is 1 to 4096.

4.

channel-group 

channel-group-number

 

mode

 

{

auto

 [

non-silent

] | 

desirable

 [

non-silent

] | 

on

} 

| {

active

 | 

passive

}

Assigns the port to a channel group, and specifies the PAgP or 
the LACP mode.

For 

channel-group-number

, the range

 

is 1 to 10. 

For 

mode

, select one of these keywords:

auto

—Enables PAgP only if a PAgP device is detected. It 

places the port into a passive negotiating state, in which the 
port responds to PAgP packets it receives but does not start 
PAgP packet negotiation. 

desirable

—Unconditionally enables PAgP. It places the port 

into an active negotiating state, in which the port starts 
negotiations with other ports by sending PAgP packets. 

on

—Forces the port to channel without PAgP or LACP. In the 

on

 mode, an EtherChannel exists only when a port group in 

the 

on

 mode is connected to another port group in the 

on

 

mode. 

non-silent

—(Optional) If your switch is connected to a 

partner that is PAgP-capable, configure the switch port for 
nonsilent operation when the port is in the 

auto

 or 

desirable

 

mode. If you do not Specifies

 non-silent

, silent is assumed. 

The silent setting is for connections to file servers or packet 
analyzers. This setting allows PAgP to operate, to attach the 
port to a channel group, and to use the port for transmission. 

active

—Enables LACP only if a LACP device is detected. It 

places the port into an active negotiating state in which the 
port starts negotiations with other ports by sending LACP 
packets.

passive

—Enables LACP on the port and places it into a 

passive negotiating state in which the port responds to 
LACP packets that it receives, but does not start LACP 
packet negotiation. 

For information on compatible modes for the switch and its 
partner, see 

PAgP Modes, page 1029

 and the 

LACP Modes, 

page 1031

. 

5.

end

Returns to privileged EXEC mode.

Command

Purpose

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

Sagem 2604 Quick Installation Manual preview
2604
Brand: Sagem Pages: 19
Draytek VigorIPPBX 2820 Series Quick Start Manual preview
VigorIPPBX 2820 Series
Brand: Draytek Pages: 29
MikroTik RouterBOARD Groove Quick Setup Manual And Warranty Information preview
RouterBOARD Groove
Brand: MikroTik Pages: 4
ZyXEL Communications P-336M Specifications preview
P-336M
Brand: ZyXEL Communications Pages: 2
NETGEAR DG834GT - 108 Mbps Super G Wireless ADSL Router Specifications preview
DG834GT - 108 Mbps Super G Wireless ADSL Router
Brand: NETGEAR Pages: 2
Alcatel Speed Touch 591s Technical User'S Manual preview
Speed Touch 591s
Brand: Alcatel Pages: 184
Supermicro AOC-MGP-i2 User Manual preview
AOC-MGP-i2
Brand: Supermicro Pages: 27
Cisco MERAKI MX450 Installation Manual preview
MX450
Brand: Cisco MERAKI Pages: 4
Patton electronics FORESIGHT 6300 User Manual preview
FORESIGHT 6300
Brand: Patton electronics Pages: 145
B&B Electronics Elinx EIR510 Series Quick Start Manual preview
Elinx EIR510 Series
Brand: B&B Electronics Pages: 2
Casablanca W-500 Technical Bulletin preview
W-500
Brand: Casablanca Pages: 13
FiberHome AN5506-04-F User Manual preview
AN5506-04-F
Brand: FiberHome Pages: 2
TP-Link Archer C7 How To Set Up preview
Archer C7
Brand: TP-Link Pages: 4
ADTRAN 239 T1 HDSL4 Installation And Maintenance Manual preview
239 T1 HDSL4
Brand: ADTRAN Pages: 20
Devolo Kurulum Manual preview
Kurulum
Brand: Devolo Pages: 24
D-Link DSL-X1852E User Manual preview
DSL-X1852E
Brand: D-Link Pages: 141
D-Link DSL-G624T Quick Installation Manual preview
DSL-G624T
Brand: D-Link Pages: 72
Zte MF283+ User Manual preview
MF283+
Brand: Zte Pages: 28

Brands by name

Popular brands

Load more brands