manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

688

Configuring IP Multicast Routing

 

Default Settings

SSM Mapping Configuration Guidelines

Guidelines and limitations for SSM mapping:

The SSM mapping feature does not have all the benefits of full SSM. Because SSM mapping takes a group join from 
a host and identifies this group with an application associated with one or more sources, it can only support one 
such application per group. Full SSM applications can still share the same group as in SSM mapping.

Enable IGMPv3 with care on the last hop router when you rely solely on SSM mapping as a transition solution for full 
SSM. When you enable both SSM mapping and IGMPv3 and the hosts already support IGMPv3 (but not SSM), the 
hosts send IGMPv3 group reports. SSM mapping does not support these IGMPv3 group reports, and the router does 
not correctly associate sources with these reports.

Default Settings

Configuring IP Multicast Routing

This section includes the following topics:

Configuring Basic Multicast Routing, page 689

 (required)

Configuring PIM Stub Routing, page 691

 (optional)

Configuring Source-Specific Multicast, page 692

Configuring SSM Mapping, page 693

Configuring a Rendezvous Point, page 697

 (required if the interface is in sparse-dense mode, and you want to treat 

the group as a sparse group)

Using Auto-RP and a BSR, page 709

 (required for non-Cisco PIMv2 devices to interoperate with Cisco PIM v1 

devices))

Monitoring the RP Mapping Information, page 709

 (optional)

Troubleshooting PIMv1 and PIMv2 Interoperability Problems, page 710

 (optional)

Feature

Default Setting

Multicast routing

Disabled on all interfaces.

PIM version

Version 2.

PIM mode

No mode is defined.

PIM RP address

None configured.

PIM domain border

Disabled.

PIM multicast boundary

None.

Candidate BSRs

Disabled.

Candidate RPs

Disabled.

Shortest-path tree threshold rate

0 kbps.

PIM router query message interval

30 seconds.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

IBM 51 Troubleshooting Manual preview
51
Brand: IBM Pages: 248
NEC N8104-213 Instructions Manual preview
N8104-213
Brand: NEC Pages: 8
Aastra CNX Product Brief preview
CNX
Brand: Aastra Pages: 2
JCG Q8 Quick Start Manual preview
Q8
Brand: JCG Pages: 2
Idis DR-6100 Series Operation Manual preview
DR-6100 Series
Brand: Idis Pages: 86
Paradyne Hotwire 6301 Installation Instructions Manual preview
Hotwire 6301
Brand: Paradyne Pages: 20
Paradyne COMSPHERE 3610 Installation Instructions preview
COMSPHERE 3610
Brand: Paradyne Pages: 2
TRENDnet TW-200 Specifications preview
TW-200
Brand: TRENDnet Pages: 2
3Com NJ220 - IntelliJack Switch User Manual preview
NJ220 - IntelliJack Switch
Brand: 3Com Pages: 82
B&B Electronics Conel UR5i v2 Libratum User Manual preview
Conel UR5i v2 Libratum
Brand: B&B Electronics Pages: 32
ZyXEL Communications ZyAIR G-3000H User Manual preview
ZyAIR G-3000H
Brand: ZyXEL Communications Pages: 299
Lanner ICS-P570 User Manual preview
ICS-P570
Brand: Lanner Pages: 63
insys icom EBW-E Quick Installation Manual preview
EBW-E
Brand: insys icom Pages: 4
OneAccess One80XM Installation Manual preview
One80XM
Brand: OneAccess Pages: 47
CAME 848EA-0120 Setup And User'S Manual preview
848EA-0120
Brand: CAME Pages: 32
hilscher netHOST NHST-T100 User Manua preview
netHOST NHST-T100
Brand: hilscher Pages: 75
V-Count Ultima Go Quick Installation Manual preview
Ultima Go
Brand: V-Count Pages: 2
ADTRAN 1700600L2 Quick Start preview
1700600L2
Brand: ADTRAN Pages: 4

Brands by name

Popular brands

Load more brands