manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

689

   

Configuring IP Multicast Routing

Configuring IP Multicast Routing

Configuring Basic Multicast Routing

You must enable IP multicast routing and configure the PIM version and the PIM mode. Then the software can forward 
multicast packets, and the switch can populate its multicast routing table.

Note: 

To enable IP multicast routing, the switch must be running the IP services image.

You can configure an interface to be in PIM dense mode, sparse mode, or sparse-dense mode. The switch populates its 
multicast routing table and forwards multicast packets it receives from its directly connected LANs according to the mode 
setting. You must enable PIM in one of these modes for an interface to perform IP multicast routing. Enabling PIM on an 
interface also enables IGMP operation on that interface.

Note: 

If you enable PIM on multiple interfaces and most of these interfaces are not part of the outgoing interface list, 

when IGMP snooping is disabled the outgoing interface might not be able to sustain line rate for multicast traffic because 
of the extra, unnecessary replication.

In populating the multicast routing table, dense-mode interfaces are always added to the table. Sparse-mode interfaces 
are added to the table only when periodic join messages are received from downstream devices or when there is a 
directly connected member on the interface. When forwarding from a LAN, sparse-mode operation occurs if there is an 
RP known for the group. If so, the packets are encapsulated and sent toward the RP. When no RP is known, the packet 
is flooded in a dense-mode fashion. If the multicast traffic from a specific source is sufficient, the receiver’s first-hop 
router might send join messages toward the source to build a source-based distribution tree.

By default, multicast routing is disabled, and there is no default mode setting. Follow this procedure to enable IP 
multicasting, to configure a PIM version, and to configure a PIM mode. This procedure is required.

BEFORE YOU BEGIN

Decide which PIM mode to use.

Ensure that the interface on which you are enabling multicast routing has an IP address assigned to it. 

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

D-Link Air DCS-1000W Setting-Up Manual preview
Air DCS-1000W
Brand: D-Link Pages: 13
NEC Express5800/E120d-M Getting Started preview
Express5800/E120d-M
Brand: NEC Pages: 2
Hama 53107 Operating Instruction preview
53107
Brand: Hama Pages: 10
H3C CR16006-F Configuration Examples preview
CR16006-F
Brand: H3C Pages: 21
Dahua DHI-NVR2104-P-4KS2 Quick Start Manual preview
DHI-NVR2104-P-4KS2
Brand: Dahua Pages: 23
SMC Networks Barricade SMC7901WBRA2 Installation Manual preview
Barricade SMC7901WBRA2
Brand: SMC Networks Pages: 2
National Instruments Fieldpoint cFP-RTD-124 Operating Instructions Manual preview
Fieldpoint cFP-RTD-124
Brand: National Instruments Pages: 15
Dust Networks SmartMesh IA-510 D2511 Manager'S Manual preview
SmartMesh IA-510 D2511
Brand: Dust Networks Pages: 30
Draytek Vigor 2700G Specifications preview
Vigor 2700G
Brand: Draytek Pages: 2
Genie IP8ESP User Manual preview
IP8ESP
Brand: Genie Pages: 6
Techroutes TSR 2800-30 Hardware Installation Manual preview
TSR 2800-30
Brand: Techroutes Pages: 20
IMC Networks iMcV-FiberLinX Operation Manual preview
iMcV-FiberLinX
Brand: IMC Networks Pages: 36
Ricoh Network Scanning Unit A Operating Instructions Manual preview
Network Scanning Unit A
Brand: Ricoh Pages: 206
XtendLan XL-VC102SB User Manual preview
XL-VC102SB
Brand: XtendLan Pages: 17
Alloy POEGE24T User Manual preview
POEGE24T
Brand: Alloy Pages: 13
TP-Link TD-8840 User Manual preview
TD-8840
Brand: TP-Link Pages: 25
SMC Networks Barricade SMC7908VoWBRA2 Specifications preview
Barricade SMC7908VoWBRA2
Brand: SMC Networks Pages: 2
Hama 53178 Instruction Manual preview
53178
Brand: Hama Pages: 45

Brands by name

Popular brands

Load more brands