Cabletron Systems ELS10-26 Reference Manual Download Page 85

Page: 85 / 170

Ethernet MIB

3-5

dot3StatsExcessiveDeferrals

{dot3StatsEntry 12}

Counter Read-Only

The number of times that transmission was deferred for an
excessive period of time.

dot3StatsFrameTooLongs

{dot3StatsEntry 13}

Counter Read-Only

The number of times a received packet was too long, since the port
was last enabled.

dot3StatsInRangeLengthErrors

{dot3StatsEntry 14}

Counter Read-Only

The number of received frames with an incorrect LLC data size.
Zero is always returned.

dot3StatsOutOfRangeLengthErrors

{dot3StatsEntry 15}

Counter Read-Only

The number of received frames with an LLC data size that is too
large (not including frames that have an Ethernet frame type field).
Zero is always returned.

dot3StatsInternalMACReceiveErrors

{dot3StatsEntry 16}

Counter Read-Only

The number of times a frame reception failed due to an error
condition not already accounted for, since the port was last
enabled.

3.3 ETHERNET-LIKE COLLISION STATISTICS GROUP

dot3CollTable

{dot3 5}

This group is minimally supported (i.e., the ELS10-26 returns a
GetResponse with a noSuchName ErrorStatus).

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands