Cabletron Systems ELS10-26 Reference Manual Download Page 74

Page: 74 / 170

2-48

TCP/IP MIB-II

::= {ctIfPortEntry 2}

ctIfPortType

OBJECT-TYPE

SYNTAX

OBJECT IDENTIFIER

ACCESS

read-only

STATUS

mandatory

DESCRIPTION

Defines the specific type of the port
(EPIM,TPIM). This is defined within
ctron oids.

::= {ctIfPortEntry 3}

ctIfPortLinkStatus

OBJECT-TYPE

SYNTAX

INTEGER

{not linked (1), linked (2), notAppli-
cable (3).}

ACCESS

read-only

STATUS

mandatory

DESCRIPTION

Defines the status of the port connec-
tion.

::= {ctIfPortEntry 4}

ctIfPort group implementation of this group is optional

The ctIfCp group contains information about the com port
configuration on the MMAC Management Modules (i.e., EMME,
TRMM) and on the MMAC-Plus Environmental Module.

ctCpTable

OBJECT-TYPE

SYNTAXSEQUENCEOF CtIfCpEntry

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands