Cabletron Systems ELS10-26 Reference Manual Download Page 131

Page: 131 / 170

ELS10-26 MIB

6-19

lxifRxQueues

{lxifEntry 19}

Counter Read-Only

Number of received packets lost because of insufficient receive
buffers.

lxifStatisticsTime

{lxifEntry 27}

Time Ticks Read-Only

Length of time during which statistics were collected. In particular,
the following statistics may be examined to determine the exact
utilization rate of a port:

• ifInOctets

• ifInUcastPkts

• ifInNUcastPkts

• ifOutOctets

• ifOutUcastPkts

• ifOutNUcastPkts

• lxifForwardedChars

• lxifFilteredChars

lxifIpAddr

{lxifEntry 28}

IP Address Read-Write

The IP address assigned to the port. If this is zero, then the port
must learn its IP address via Reverse ARP or PPP’s IPCP.

lxifIpGroupAddr

{lxifEntry 29}

IP Address Read-Write

Zero, or an IP group address assigned to the port.

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands