Cabletron Systems ELS10-26 Reference Manual Download Page 13 | Manualshive

Page: 13 / 170

background image

Introduction

1-3

1.2 GETTING HELP

If you need additional support related to the ELS10-26, or if you
have any questions, comments, or suggestions concerning this
manual, contact Cabletron Systems Global Call Center:

Phone:

(603) 332-9400

Internet mail:

[email protected]

FTP:

ctron.com (134.141.197.25)

Login: anonymous
Password:

your email address

BBS:

(603) 335-3358

Modem setting:

8N1: 8 data bits, No parity, 1 stop bit

Before calling Cabletron Systems Global Call Center, have the
following information ready:

• Your Cabletron Systems contract number

• A description of the failure

• The serial and revision numbers of all Cabletron Systems

products in the network

• A description of any action(s) already taken to resolve the

problem (e.g., changing mode switches, rebooting the unit, etc.)

• A description of your network environment (layout, cable type,

etc.)

• Network load and frame size at the time of trouble (if known)

• The device history (i.e., have you returned the device before, is

this a recurring problem, etc.)

• Any previous Return Material Authorization (RMA) numbers

For additional information about Cabletron Systems products,
visit our World Wide Web site: http://www.cabletron.com

«
...
11
12
13
14
15
...
»

Summary of Contents for ELS10-26











































































































































































Reviews:

No comments

Related manuals for ELS10-26

Brand: Xantrex Pages: 8

Brand: EAW Pages: 6

Brand: EAW Pages: 6

LS42 - BladeCenter - 7902

Brand: IBM Pages: 56

Brand: IBM Pages: 2

BladeCenter Management Module

Brand: IBM Pages: 78

Brand: IBM Pages: 110

Remote Supervisor Adapter II

Brand: IBM Pages: 132

Brand: National Instruments Pages: 17

Brand: National Instruments Pages: 16

Brand: National Instruments Pages: 23

Brand: Danfoss Pages: 61

Brand: D-Link Pages: 176

Brand: H3C Pages: 12

RealPort Ethernet 10/100

Brand: Xircom Pages: 30

Brand: Tektronix Pages: 178

CNPS11X Extreme

Brand: ZALMAN Pages: 12

Brand: ZyXEL Communications Pages: 79

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands