Cabletron Systems ELS10-26 Reference Manual Download Page 65 | Manualshive

Page: 65 / 170

background image

TCP/IP MIB-II

2-39

InterfacePortLinkDown

Specific Trap Type Code - 0x1A3

This trap will be generated when a previously attached bridging
port has been disconnected from a LAN. This is only appropriate
for ports that support the concept of a link state. The information
will include:

ctIfNumber

{ctIfEntry 1}

ctIfPortPortNumber

{ctIfPortEntry 1}

This trap will be sent when a link goes down.

2.17 CABLETRON MIB 2 EXTENSIONS

ctmib2-ext-mib Cabletron’s extension to the MIB-II

This module provides authoritative definitions for part of the
naming tree below:

cabletron {enterprises 52}

This module will be extended, as additional sub-sections of this
naming tree are defined.

IMPORTS ctronMib2FROM CTRON-MIB-NAMES OBJECT-TYPE
FROM RFC-1212

Textual Convention

DisplayString ::= OCTET STRING

This data type is used to model textual information from the NVT
ASCII character set. By convention, objects of this syntax are
declared as having: SIZE (0.255)

«
...
63
64
65
66
67
...
»

Summary of Contents for ELS10-26











































































































































































Reviews:

No comments

Related manuals for ELS10-26

Vb-C60 - Ptz Network Camera

Brand: Canon Pages: 30

Brand: Rain Bird Pages: 17

Brand: Lindy Pages: 4

ACC-CX3RDK-CU5640

Brand: e-con Systems Pages: 9

Brand: Lancom Pages: 25

Converter Board R0E5212BACFG00

Brand: Renesas Pages: 6

Brand: ZyXEL Communications Pages: 5

Brand: A4Tech Pages: 7

18x18 Card Cage

Brand: WolfPack Pages: 31

Brand: ACTi Pages: 12

Brand: Aaeon Pages: 72

Brand: Juniper Pages: 420

Brand: Zoom Pages: 31

Brand: Tripp Lite Pages: 2

Brand: Airlinkplus Pages: 20

Brand: ZyXEL Communications Pages: 2

Brand: Rosco Pages: 20

Brand: ST Pages: 67

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands