Cabletron Systems ELS10-26 Reference Manual Download Page 38 | Manualshive

Page: 38 / 170

background image

2-12

TCP/IP MIB-II

ipReasmOKs

{ip 15}

Counter Read-Only

The number of IP datagrams which were successfully reassembled.

ipReasmFails

{ip 16}

Counter Read-Only

The number of failures (for whatever reason timed-out, errors, etc.)
detected by the IP reassembly algorithm. This is not necessarily a
count of discarded IP fragments since some algorithms (notably
RFC 815) can lose track of the number of fragments by combining
them as they are received.

ipFragOKs

{ip 17}

Counter Read-Only

The number of IP datagrams that have been successfully
fragmented within this ELS10-26.

ipFragFails

{ip 18}

Counter Read-Only

The number of IP datagrams that have been discarded because
they needed to be fragmented but could not be (e.g., because their
“Don’t Fragment” flag was set).

ipFragCreates

{ip 19}

Counter Read-Only

The number of IP datagram fragments that have been generated
by this ELS10-26.

2.4.1 IP Address Table

The TCP/IP IP Address Table contains the IP addressing
information for each port. The parameters are described below.

«
...
36
37
38
39
40
...
»

Summary of Contents for ELS10-26











































































































































































Reviews:

No comments

Related manuals for ELS10-26

EtherLink 3C509B

Brand: 3Com Pages: 8

Brand: 3Com Pages: 8

Brand: Q-See Pages: 2

Brand: FOR-A Pages: 39

AirStation WHR-G300N

Brand: Hornington Pages: 6

AyrMesh IndoorAP

Brand: AYRSTONE Pages: 2

Brand: Advantech Pages: 50

Brand: Idis Pages: 20

UniFi LED ULED-AT

Brand: Ubiquiti Pages: 16

Brand: ANEP Pages: 48

Brand: Hama Pages: 25

Brand: Infoblox Pages: 16

Brand: IBM Pages: 72

Brand: ACTi Pages: 14

Brand: Z-Wave Pages: 42

Brand: ExtraHop Pages: 2

Brand: AMD Pages: 27

Brand: EXAGATE Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands