Cabletron Systems ELS10-26 Reference Manual Download Page 109 | Manualshive

Page: 109 / 170

background image

PPP MIB

5-11

pppIpEntry

{pppIpTable 1}

Not-Accessible

IPCP status information for a particular PPP link.

pppIpOperStatus

{pppIpEntry 1}

Integer Read-only

The operational status of the IP network protocol. If the value of
this object is up, then the finite state machine for the IP network
protocol has reached the Opened state.

• opened (1) - the IPCP protocol is in open state.

• not-opened (2) - the IPCP protocol is in anything but the open

state.

pppIpLocalToRemoteCompressionProtocol{pppIpEntry 2}
Integer Read-only

The IP compression protocol that the local PPP-IP entity uses when
sending packets to the remote PPP-IP entity. The value of this
object is meaningful only when the link has reached the open state
(pppIpOperStatus is opened).

• none (1) - no IP compression protocol supported.

• vj-tcp(2) - the Van Jacobsen TCP/IP header compression

protocol is supported.

The ELS10-26 does not support protocol compression.

pppIpRemoteToLocalCompressionProtocol{pppIpEntry 3}
Integer Read-only

The IP compression protocol that the remote PPP-IP entity uses
when sending packets to the local PPP-IP entity. The value of this
object is meaningful only when the link has reached the open state
(pppIpOperStatus is opened).

• none (1) - no IP compression protocol supported.

«
...
107
108
109
110
111
...
»

Summary of Contents for ELS10-26











































































































































































Reviews:

No comments

Related manuals for ELS10-26

Brand: BandLuxe Pages: 67

Brand: SAF Pages: 30

Brand: Conceptronic Pages: 230

Brand: BSD Networks Pages: 7

Brand: Allied Telesis Pages: 1

CompactPCI CC8-BLUES

Brand: EKF Electronik Pages: 52

Brand: Supersonic Pages: 46

Brand: Xantech Pages: 4

E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV 27-9-2010

Brand: Juniper Pages: 122

D-NVR4108HS-4KS2/L

Brand: Dahua Pages: 33

Brand: axing Pages: 4

Brand: ZALMAN Pages: 18

Brand: AMX Pages: 1

Brand: Hunter Pages: 2

Brand: Keysight Technologies Pages: 106

Serial Attached SCSI (SAS) Expander Card

Brand: Adaptec Pages: 26

Brand: Microcomputer Systems Pages: 21

Brand: Digisol Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands