Cabletron Systems ELS10-26 Reference Manual Download Page 83

Page: 83 / 170

Ethernet MIB

3-3

dot3StatsTable

{dot3 2}

Not Accessible

A list of interface entries; one per Ethernet port, which correspond
to the dot3Table entries.

dot3StatsEntry

{dot3StatsTable 1}

Not Accessible

A set of statistics for an Ethernet entry. The individual components
are described below.

dot3StatsIndex

{dot3StatsEntry 1}

Integer Read-Only

The ELS10-26’s Ethernet port number.

dot3StatsAlignmentErrors

{dot3StatsEntry 2}

Counter Read-Only

Number of received packets with frame alignment errors since the
port was last enabled.

dot3StatsFCSErrors

{dot3StatsEntry 3}

Counter Read-Only

Number of received packets with FCS errors (and without frame
alignment errors) since the port was last enabled.

dot3StatsSingleCollisionFrames

{dot3StatsEntry 4}

Counter Read-Only

The number of frames that experienced a single collision.

dot3StatsMultipleCollisionFrames

{dot3StatsEntry 5}

Counter Read-Only

The number of successfully transmitted frames that experienced
more than one collision.

Summary of Contents for ELS10-26











































































































































































Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands

Cabletron Systems ELS10-26, Reference Manual

Search results

Summary of Contents for ELS10-26

Reviews:

Related manuals for ELS10-26

Brands by name

Popular brands